giordan car alarm remote start g686 s
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=111972
Printed Date: July 14, 2025 at 9:29 AM
Topic: giordan car alarm remote start g686 s
Posted By: jaychris0708
Subject: giordan car alarm remote start g686 s
Date Posted: February 27, 2009 at 8:28 AM
Hey All, Just wanted to get some help on my remote start system it won't start...... i think the problem is that it said in the manual it has a brown wire on the relay but there's none but instead its white..... i don't whats happening but when i press the bell button to start it it won't start it just does the crank noise can some some one help me please?????
Replies:
Posted By: howie ll
Date Posted: February 27, 2009 at 5:17 PM
What vehicle, might you have a factory transponder that hasn't been by-passed?
Posted By: jaychris0708
Date Posted: February 27, 2009 at 6:52 PM
i have a 2003 mitsubishi lancer vrx ch
Posted By: howie ll
Date Posted: February 28, 2009 at 3:43 AM
Try it with the key in the ignition, if it starts you haven't by-passed the transponder.
Posted By: jaychris0708
Date Posted: February 28, 2009 at 10:53 PM
nah i tried that and its still doesn't wana turn on with the remote, well my friend said that we done it right but it says in the manual hook a brown wire which it didn't have a brown wire, it had the white wire....... cause when i try to turn it on it clicks but it doesnt turn on it goes back to off.....
Posted By: howie ll
Date Posted: March 01, 2009 at 2:49 AM
Stop panicking and tell me is this brown or white wire from the alarm or from the car and what's it's function? If it's the wrong colour have you tested it to see if it's the right function? What actually happens when you try it, do the ign lights come on? Test all it's functions, I've no idea what a giordan alarm is, never heard of them. Any technical back-up in Strine or NZ because if there isn't you're shafted. I'm still betting on a missing ign wire, transponder or tach.
Posted By: jaychris0708
Date Posted: March 01, 2009 at 2:44 PM
well in the diagram it suppose to be white from the alarm to the relay and then brown from relay from to the cylinder on..... but instead it's all white instead of white and brown...... and yes the light ingnition come on and off when i try to start with the remote so we don't know if that is right.
Posted By: howie ll
Date Posted: March 01, 2009 at 4:16 PM
What's the relay a starter kill?
Posted By: jaychris0708
Date Posted: March 01, 2009 at 4:34 PM
YEP
Posted By: howie ll
Date Posted: March 01, 2009 at 5:57 PM
Don't use it, check the tach, ie have you programmed it correctly? If it cranks and you get the ignition lights on you've basicly done every thing, have you wired up ALL the outputs from the ignition switch? I'm still about not sure about it not starting even when the key is in the ignition, I have a 2000 Galant which has a transponder, I've done loads of Evos also with transponders, I was sure that a 2003 especially if New Zealand uses Aussie rules would have had a transponder immobiliser.
Posted By: jaychris0708
Date Posted: March 01, 2009 at 6:07 PM
Well my friend was asking there is a wire in the diagram that suppose to go to the oil switch centre, but also it said it can go to the ignition switch... which we put it in too would this be right? and also on the starter relay there's a yellow wire how does this correctly hook up?
Posted By: howie ll
Date Posted: March 01, 2009 at 6:35 PM
I really can't help you anymore, if you have a wiring diagramme please post it, I'm worried about the wire going to oil pressure switch, on a decent unit that would be the tach wire.
Posted By: jaychris0708
Date Posted: March 01, 2009 at 7:23 PM
it's all good buddy i know you done all your best to help but yeah im so confuse on this but yeah if i have anymore question i'll email you or sumting do you have msn messenger....... i talk to you then there?????
Posted By: jaychris0708
Date Posted: March 01, 2009 at 7:53 PM
hey bud i have the diagram but it's to big to attach it do have an email address and i'll email it to you.....
Posted By: howie ll
Date Posted: March 02, 2009 at 11:25 AM
You've got to look at the other post on this subject by cha209. I think they are in a parallel universe with similar (Chinglish) problems.
Posted By: jaychris0708
Date Posted: March 02, 2009 at 2:29 PM
hey Howie Bro thanks so much i think this is the answer i really need with the things im having problems with thanks again bud...... I'll let you know how i got with this when we fix it......
Posted By: jaychris0708
Date Posted: March 02, 2009 at 10:22 PM
Hey all just wanted to ask if this product will blow up the starter motor of mitsubishi 2003 lancer cause i've just got told about it that why... will it?????
Posted By: chriswallace187
Date Posted: March 04, 2009 at 4:18 AM
In all honesty, the fact that it has an "oil-pressure sensor" wire speaks volumes. This means of sensing that the engine's started was abandoned by reputable manufacturers years ago.
The starter motor could be damaged if the remote start continued to crank after the engine was running. Though this might happen, the system installed here will probably just get confused and shut down even though it's started just fine.
As howie said, systems with tach sensing are much easier to install and more reliable.
-------------
C Renner's Auto Electronix
My service is cheap, quick, and good - pick any two
|