clifford 50.5x into a 99 prelude
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=113963
Printed Date: May 20, 2024 at 6:27 PM
Topic: clifford 50.5x into a 99 prelude
Posted By: kaylude
Subject: clifford 50.5x into a 99 prelude
Date Posted: May 22, 2009 at 6:37 PM
hey guys i just bought a clifford 50.5x planning to put it in my 99 prelude
do you guys have the wiring diagram picture for the alarm by any chance or any diy ?
Replies:
Posted By: howie ll
Date Posted: May 23, 2009 at 2:16 AM
Yes, here's the trick. Go to vehicle wiring on the header section,click on it, look up Honda, go down to 1999, then Prelude then click on vehicle security and remote start.
Posted By: kaylude
Date Posted: May 23, 2009 at 4:50 AM
yeah i tried that but the wiring diagram .. some dont match with the one in the clifford manual.. do you want me to list which ones i dont know ? haha
Posted By: t&t tech
Date Posted: May 23, 2009 at 6:23 AM
you could probably look in the downloads section, i dunno for sure if it is there, but, just a thought. if you don't find it there then maybe you should post which wire you're not sure about and maybe those who are familiar with clifford products will chime in, cheers ------------- COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: howie ll
Date Posted: May 23, 2009 at 12:54 PM
Yes tell us what you're not sure about, t&t it ain't a genuine Clifford, there's been no such beast since the days of G4 and that's half the problem.
Posted By: kaylude
Date Posted: May 25, 2009 at 3:03 AM
okay here it is , in the clifford 50.5x instruction guide book
primary harness ( h1 ), 12 - pin connectors
from book to my car
RED / white (-) 200mA channel 2 validity output -> RED / white
red (+) constant power input -> red
brown (+) siren output -> red on siren ?
black ground -> black or chassis
violet (+) door trigger input, zone 3 -> ?
blue (-) mulitplexed input, zone 4 -> ?
green (-)door trigger input ,zone 3 -> WHITE/ black ?
BLACK/ white (-) 200 mA domelight output -> ?
WHITE/ blue (-) remote start activation input -> ?
white (+)/(-) selectable light flash output -> ?
orange (-) 500 mA armed output -> green ?
thanks guys
Posted By: howie ll
Date Posted: May 25, 2009 at 3:34 AM
RED / white to control a (factory) electric trunk release. Red to white at ignition. Brown to red of siren, bring siren leads into cabin and ground both blacks at a body bolt in kickpanel or behind dash. Violet don't use Green to WHITE/ black door contact as wiring info here. Blue to trunk contact, again as wiring info here.* BLACK/ white don't use. White to parking lights, + or - as wiring info here. Oranfe, not used unless you're incorporsting window closers. *There should be a grey wire on the alarm for hood input, if not join your hood switch to the blue via 2 diodes, bands away from the alarm. From your questions, should you really be doing this?
Posted By: kaylude
Date Posted: May 25, 2009 at 4:01 PM
thanks howie ll
well im new at this that's why i want to ask someone that have some experience with this before hand
reason why im doing this is because i want to learn while im doing
if you know a guide someone where or a diy then can you send me the link thanks
Posted By: howie ll
Date Posted: May 25, 2009 at 4:42 PM
OK, just proceed at your own pace, if you ask a question I perceive as simplistic or silly I will point it out and give you some leeway.
Posted By: kaylude
Date Posted: May 25, 2009 at 5:50 PM
thanks howie ll
sorry i know its a hassle but since your like a guru .. i rather ask someone then messing up my own car -__-
Posted By: kaylude
Date Posted: June 04, 2009 at 2:10 AM
auxiliary harness (H2) , 6- pin connector
light blue ->
WHITE/ black ->
violet/black ->
GREEN / WHITE ->
gra/black ->
light green /black ->
door lock harness, 3 pin connector
light blue (+) lock ( - ) unlock output -> ?
green ( -) lock ( +) unlocke out put -> ?
|