08 acura tsx
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=114180
Printed Date: September 12, 2025 at 10:43 AM
Topic: 08 acura tsx
Posted By: mike08401
Subject: 08 acura tsx
Date Posted: June 02, 2009 at 6:43 PM
I tried to install starter/alarm in my sister 08 acura tsx but i'm stuck because i'm really confused about factory DisArm and rearm wire the diagram just show only disarm also it stated in side driver door(FACTORY ALARM DISARM WHITE (-) @ DRIVERS DOOR MODULE IN DRIVERS DOOR ) so my question is : Do i have to find wire inside the door and connect it there or it should be connect some where in side car under dash... I've tried to trace the white wire with silver dot it go inside car but show no contact I really need help to find this wire
Many thanks
Replies:
Posted By: tommy...
Date Posted: June 02, 2009 at 7:00 PM
yes...to my knowledge that is the only place to get it...There are units you can buy to control door locks/factory security.
-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
Posted By: mike08401
Date Posted: June 02, 2009 at 8:22 PM
Hi tommy!
What's part you are talking about? Do you have any sugestion how to run this wire from/to that port???
Thanks
Posted By: tommy...
Date Posted: June 02, 2009 at 9:35 PM
 XK01 - Programmable Platform# 01: Door Lock & Alarm Interface
Firmware: HODL4 2.00 ------------- M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
Posted By: tommy...
Date Posted: June 02, 2009 at 9:39 PM
CANMAX400 Multi Function Programmable Vehicle Interface
Firmware: 400.HONDA4 0.09 Combination of Immobilizer Bypass and Data Bus Door Lock Control | | |
------------- M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
Posted By: cliffordtech82
Date Posted: June 03, 2009 at 10:21 PM
Try going into drivers door and you will find a white and red for your arm and a white for your disarm. Goodluck
Posted By: Velocity Motors
Date Posted: June 04, 2009 at 8:57 AM
You can use a data module to control the alarm features as well as bypass the OEM immobilizer. It's way easier and no need to run wires into the door. The door also has a molex which is a tremendous PITA for anyone to have to run wires through it.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: tommy...
Date Posted: June 04, 2009 at 9:00 AM
Ditto ...If it is your first adventure w/ molex...By-pass will work fine...Pretty easy install... Velocity Motors wrote:
You can use a data module to control the alarm features as well as bypass the OEM immobilizer. It's way easier and no need to run wires into the door. The door also has a molex which is a tremendous PITA for anyone to have to run wires through it.
------------- M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!
Posted By: mike08401
Date Posted: June 04, 2009 at 7:40 PM
Thank You all for repplied after some research and sugestion I think I will go with Idatalink module which control door and immob. too
Once again The12volt is the #1 place to get help
|