Print Page | Close Window

dei 561r on 97 camry

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=114256
Printed Date: September 10, 2025 at 1:13 PM


Topic: dei 561r on 97 camry

Posted By: apoorvahp
Subject: dei 561r on 97 camry
Date Posted: June 05, 2009 at 1:32 PM

I am trying to install dei 561r on a 97 camry and its my first time installing a security system on the car so can anyone please help me install it by tell me what to do.

Thanks in advance to everyone



Replies:

Posted By: joch1314
Date Posted: June 05, 2009 at 2:53 PM

Have you ever installed anything in a car before?  This isn't to difficult a car, but can be if you don't have any experience with remote starts or how to test for wires? 

Here's the wiring diagram:

BatteryWHITE(+)IGNITION SWITCH HARNESS
posted_imageIgnition 1BLACK / YELLOW(+)IGNITION SWITCH HARNESS
posted_imageIgnition 2BLACK/ RED(+)IGNITION SWITCH HARNESS
posted_imageAccessory 1BLUE/RED(+)IGNITION SWITCH HARNESS
posted_imageStarter 1RED(+)IGNITION SWITCH HARNESS
posted_imageAnti-Theft TypeUNIVERSAL IMMOBILIZER
posted_imageKey SenseRED / BLUE(-)IGNITION SWITCH HARNESS
posted_imageTachometerYELLOW/RED(AC)AT IGNITION COIL
posted_imageSpeed SenseVIOLET / YELLOW(AC)IN HARNESS IN PASSENGER KICKPANEL
posted_imageParking LightsGREEN(+)AT VEHICLE FUSE PANEL
posted_imageBrake LightsGREEN / WHITE(+)AT SWITCH ABOVE BRAKE PEDAL
posted_imageReverse LightsRED / BLACK(+)AT VEHICLE FUSEBOX
posted_imageHornGREEN/ BLACK(-)IGNITION SWITCH HARNESS
    
 < color=#3a437f>Note: Audiovox makes no representation or warranty with respect to the above information including its accuracy, completeness, or its freedom from third parties' proprietary rights. Audiovox disclaims all liability or responsibility for errors or omissions therein or any decision made by the recipient in reliance thereon. The installer must verify any circuitry with the proper test equipment prior to installation. 
  

Here's the door locks:

Power UnlockDARK BLUE(-)IN ORANGE PLUG AT VEHICLE FUSE PANEL
posted_imagePowerLockDARK BLUE/WHITE(-)IN ORANGE PLUG AT VEHICLE FUSE PANEL
posted_imageDriver Mtr UnlockBLUE(+)IN HARNESS IN DRIVERS KICKPANEL
posted_imageDriver Mtr LockBLUE/RED(+)IN HARNESS IN DRIVERS KICKPANEL

Should be everything you need....and don't be afraid to ask Q's!



-------------
...half of the truth can be worse than a lie. <----Roger Russell said that..




Posted By: apoorvahp
Date Posted: June 07, 2009 at 6:49 PM
I tried installing it today but I didnt know if I should cut the wire or do something else, so can anyone advice me what to do next.




Posted By: KarTuneMan
Date Posted: June 09, 2009 at 12:10 PM

A soldering iron, digital multimeter, and basic ability are 3 KEY things to have. Do you have all of these?

If not regroup, and start again, or get some help! Not help from your laptop, I mean a real live person.






Print Page | Close Window