Print Page | Close Window

where is pats module in 2000 explorer

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=114687
Printed Date: March 29, 2024 at 10:06 AM


Topic: where is pats module in 2000 explorer

Posted By: desitdt
Subject: where is pats module in 2000 explorer
Date Posted: June 25, 2009 at 3:21 PM

I have a 2000 Ford Explorer and i need to find the Pats immobilizer to hook the bypass to. Where is it in the 2nd Gen Explorer?



Replies:

Posted By: spookiestylez
Date Posted: June 25, 2009 at 3:45 PM
what kind of remote start, and what kind of bypass module are you trying to use. That way I can just attach you a pdf instructions if you don't have a install guide.

-------------
RTFM




Posted By: desitdt
Date Posted: June 25, 2009 at 4:00 PM
its a ready remote remote start and a DEI 555p bypass. I have instructions for both, just neither tel me where the actual module is.




Posted By: desitdt
Date Posted: June 25, 2009 at 4:41 PM
anyone?




Posted By: howie ll
Date Posted: June 25, 2009 at 5:19 PM
It doesn't go to the pats module, it picks up the antenna around the ignition switch and you take the wiring from that antenna.




Posted By: spookiestylez
Date Posted: June 25, 2009 at 5:30 PM
howie ll wrote:

It doesn't go to the pats module, it picks up the antenna around the ignition switch and you take the wiring from that antenna.

That is correct.
The bypass you have is pretty easy to install. I've attached a pdf file of the instructions for the 555p.

555p.pdf

Cheers

-------------
RTFM




Posted By: desitdt
Date Posted: June 25, 2009 at 5:53 PM
ok well im having a real hard time with this. Can somone help me find exactly where these wires go? i already have those instructions but i dont get pin 3, 4 and the 2 ignitions.




Posted By: desitdt
Date Posted: June 25, 2009 at 6:06 PM
Ive taken some pictures for help. I Also cannot find the horn wire.Some of the pictures are to try and help me find the horn wire and some are for the bypass.









Posted By: desitdt
Date Posted: June 25, 2009 at 6:07 PM
https://s281.photobucket.com/albums/kk210/desitdt/




Posted By: spookiestylez
Date Posted: June 25, 2009 at 6:24 PM
I just tried to post back, and I got logged out for some reason.

On the 555P pin 3 is the (-) remote start input.
this wire is going to be connected to the blue (-) ground when running/status output wire or to the blue/white (-) 2nd status output wire from your remote start.

Pin 4 on the 555p is not going to be used in your install, so tape it off.

The 2 ignitions mean that you are going to have to cut your factory ignition wire in half. Then attach the pink wire from the 555p to the side that goes to the ignition switch, and the pink/white to the opposite wire.
Here is a wiring diagram for your car
EDIT: link corrected

-------------
RTFM




Posted By: desitdt
Date Posted: June 25, 2009 at 6:31 PM
hey thanks for the help but the link doesnt work. And i meant pin 3,4 on the immobilizer (pin 5 and 6 on the bypass)




Posted By: desitdt
Date Posted: June 25, 2009 at 6:35 PM
sorry pin 5 and 7 on the bypass




Posted By: desitdt
Date Posted: June 25, 2009 at 7:04 PM
i found the horn wire but i still dont understand pin 5 and 7. Also when i cut the ignition wire you mean the heavy guage wire in the ignition harness right?




Posted By: desitdt
Date Posted: June 27, 2009 at 3:15 PM
bump still dont know where pin 5 and 7 go and what to do where it say ignition car and key side




Posted By: JWorm
Date Posted: June 28, 2009 at 2:02 PM
In the PATS harness one of the wire tests as an ignition wire (power when key is turned on). That is where pin 5 and 7 go to (after cutting it).





Print Page | Close Window