Print Page | Close Window

1998 olds delta 88

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=115908
Printed Date: May 15, 2024 at 4:20 AM


Topic: 1998 olds delta 88

Posted By: skipastaria
Subject: 1998 olds delta 88
Date Posted: August 25, 2009 at 6:49 PM

i have an olds delta 88 1998 and the keyless entry does not work i put a new battery in it and still nothing how do i find and check the module that controls the door locks



Replies:

Posted By: t&t tech
Date Posted: August 26, 2009 at 9:24 PM
Do you have any interior controls for the locks?

-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF. PSALMS 37:5




Posted By: tommy...
Date Posted: August 26, 2009 at 9:31 PM
On some of the GM's ...After you replace battery...You have to press lock/unlock at the same time for 6-10 seconds...Not sure if that applies here...?!

-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!




Posted By: tommy...
Date Posted: August 26, 2009 at 9:45 PM

PROGRAMMING

Early 1999 Pontiac Grand am

1.      Make sure ignition is in the OFF position.

2.      Locate the Programming Connector in the trunk (driver’s side). It is a plastic connector with two wires leading up to it. The connector is not plugged into anything. You may have to pull back trim to access the connector.

3.      The programming connector should have two terminals. Connect both terminals with a suitable jumper wire. Make sure the terminals remain connected throughout the programming procedure.

4.      Press the LOCK and UNLOCK buttons on the transmitter simultaneously. In response, the Keyless Entry Module will cycle all the Door Lock Motors at once. Your new remote has been accepted and all existing remote codes have been erased.

5.      Repeat the previous step for each additional transmitter (including any existing transmitters). Do not remove jumper wire in between programming of transmitters.

6.   Remove the jumper wire from the Keyless Programming Connector.

PROGRAMMING

2000  Pontiac Grand am

1. Close all doors.

2. Press and hold the Unlock button on door lock switch on drivers door.
    Hold until instructed to release.

3. Insert and remove key from ignition 2 times. Do Not turn ignition.

4. Insert key in ignition a third time and leave key in ignition. Do Not turn ignition.
   
5. Release door lock switch on drivers door panel.
    A Chime will sound 3 times indicating that you are in programming mode.

6. Press both the Lock and Unlock buttons on the remote up to 30 seconds.
    A chime will sound 2 times if remote has programmed successful.

7. Repeat step 6 if you are programming additional remotes.

8. Remove key from ignition to exit programming mode

programming instructions

2002 2003 2004

the manufacturer’s programming instructions for your vehicle make model and year specify diagnostic programming required

You will need to visit your local dealer or locksmith to have your remote programmed to your car using diagnostic equipment



-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!




Posted By: tommy...
Date Posted: August 26, 2009 at 9:46 PM

PROGRAMMING INSTRUCTIONS

1996-1997 Aurora

1.Turn ignition OFF

2.Access DATA LINK CONNECTOR (DLC) , next to steering column

3.Use fused jumper wire, jump connectors 4 & 8 in DLC

4.Turn ignition to ON

5.To PROGRAM…

6.…Press and hold LOCK & UNLOCK remote buttons  at same time

7.…Doors will lock and unlock to let you know the remote has been programmed

8.Repeat steps 6 & 7 for additional remotes

9.Take jumper wire our to exit programming mode

- Additional functions and feedback settings can be set to respond to the remote transmitters – see dealer

PROGRAMMING INSTRUCTIONS

1998-1999 Aurora

1.Turn ignition OFF

2.Access DATA LINK CONNECTOR (DLC) , next to steering column

3.Use fused jumper wire, jump connectors 4 & 8 in DLC

4.Close all doors

5.Turn ignition to ON

6.Doors will lock

5.To PROGRAM…

6.…Press and hold LOCK & UNLOCK remote buttons  at same time for 30 seconds

7.…Doors will lock and unlock to let you know the remote has been programmed

8.Repeat steps 6 & 7 for additional remotes

9.Take jumper wire our to exit programming mode

Still looking to find remote programming for you...!



-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!




Posted By: skipastaria
Date Posted: August 29, 2009 at 8:18 AM
yes there are interior controls





Print Page | Close Window