viper 5701, error, pairing instructions?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=116530
Printed Date: May 03, 2024 at 3:58 AM
Topic: viper 5701, error, pairing instructions?
Posted By: rutcgr18
Subject: viper 5701, error, pairing instructions?
Date Posted: September 24, 2009 at 9:28 PM
Got a new 2 way remote. Prgramed it. Seem to work fine. Now i hit the lock or unlock button and it unlocks and locks but also gives me a error sound. I have del the remote from the unit i need to add it again and see if that fixes it. Who has the pariing instuctions?. THoughts on the other problem??
Replies:
Posted By: kgerry
Date Posted: September 25, 2009 at 9:44 AM
unplug the 12? pin harness that powers the brain for a minute or so and plug it back in.... these units had issues with the out-of-range notification circuit, that was remedied by "rebooting" the brain.....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: rutcgr18
Date Posted: September 25, 2009 at 10:33 AM
thanks does any one have the steps to add a remote??
Posted By: kgerry
Date Posted: September 25, 2009 at 2:07 PM
i uploaded the programming guide
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: rutcgr18
Date Posted: September 26, 2009 at 7:46 PM
kgerry wrote:
i uploaded the programming guide
Thanks
I have add the remote still having problem. I have unplugged my brain for 3 hours and it is still doing it. Is there a firmware upgrade for these things. It really anyoing. I am thinking about just buying a new system. Not happy with DEI on this one.
Posted By: rutcgr18
Date Posted: September 26, 2009 at 7:55 PM
I found this info any one have any incite on this?? Directed will be shipping out new brians in the next few months with a firmware update that resolves this issue completely. Depending on where it was purchased, I would believe most retailers will do a swap for you when those are shipped and become available. In the meantime there is a fix. Place a 10,000 ohm resistor in series with the blue wire on the antenna lead as close to the brain as possible. Hope this helps!
Posted By: rutcgr18
Date Posted: September 29, 2009 at 4:50 PM
Bump no one can help on this one. Can i update the firmware on this thing? Thanks
mike
Posted By: xtremej
Date Posted: September 29, 2009 at 4:55 PM
no you cannot, just add the 10k ohm resistor to the antenna lead as described.
Posted By: rutcgr18
Date Posted: September 29, 2009 at 5:15 PM
xtremej wrote:
no you cannot, just add the 10k ohm resistor to the antenna lead as described.
what does that acutally do?
Posted By: vipersport328
Date Posted: January 18, 2010 at 8:37 PM
I have the same problem with my 5701 two way remote. Unplugged the brain and still have the same problem. Has anyone added the 10k ohm resistor in series? Just seeing if that works. Thanks
-------------
Pete
Posted By: yimke
Date Posted: January 19, 2010 at 10:08 AM
Are you using any D2D device? If so, manually wire in your lock/unlock via the harness to your 3 pin on the brain. Then snip the red and white wires on the D2D cable. If that works then it was D2D.
Posted By: vipersport328
Date Posted: January 19, 2010 at 12:14 PM
I am using an XK01 but I did not use the D2D cable I manually connected all the wires. Thanks
------------- Pete
Posted By: jeremytravis
Date Posted: January 19, 2010 at 8:32 PM
Have you tried replacing the battery in the remote, or checked the antenna cable and connections, sometimes the wires at the harness that plugs into the antenna get pinched.
-------------
**ADVANCED MECP CERTIFIED
Posted By: vipersport328
Date Posted: January 20, 2010 at 4:01 AM
I have replaced the batteries no help. I will check the antenna wires to see if they are pinched. What about putting the 10kohm resistor does that work.
Thanks
-------------
Pete
Posted By: ashleytingle
Date Posted: September 06, 2010 at 7:59 PM
I am having the exact same problem. Has anyone tried the resistor fix????
|