push button start, 2007 vw jetta?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=116863
Printed Date: June 10, 2024 at 5:47 AM
Topic: push button start, 2007 vw jetta?
Posted By: mitch0627
Subject: push button start, 2007 vw jetta?
Date Posted: October 09, 2009 at 5:39 PM
Hello Guys:
I decided to install a NIKEN, push Start button, unfortunately the instructions don't tell me much, I was wondering if you could indicate me how to do so myself? The instructions only say:
1 Connect the push button to the relay. (Done)
2 The Black wire to ground (Done)
3 THE GREEN WIRE SHOULD BE CONNECTED TO TERMINAL 15(IGN)BEHIND THE IGNITION 4 SWITCH, WITH ANOTHER ONCE CONNECTING TERMINAL 50, BEHIND THE IGNITION SWITCH AS WELL
5 THE RED WIRE SHOULD BE CONNECTED TO TERMINAL 15
These are all the steps, as you can see, I only done 2, the other steps I am not so sure. Could you please tell me what to do exactly on a 2007 vw jatta
thanks
Replies:
Posted By: t&t tech
Date Posted: October 09, 2009 at 6:13 PM
OH DEAR!  ------------- COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: mitch0627
Date Posted: October 10, 2009 at 6:28 PM
im looking for the ignition diagram (colors and all ) for a 2007 vw jetta
thanks
Posted By: i am an idiot
Date Posted: October 10, 2009 at 6:32 PM
Posted By: mitch0627
Date Posted: October 10, 2009 at 8:41 PM
IGNITION Yellow On back of ignition switch +
Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge.
ACCESSORY Green On back of ignition switch +
Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge.
STARTER Red On back of ignition switch +
Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge.IGNITION Yellow On back of ignition switch + Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge. ACCESSORY Green On back of ignition switch + Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge. STARTER Red On back of ignition switch + Remove the plastic cover around the steering column and you will see a small black box mounted to column held by 1 torx screw. Remove this box to expose the ignition key wires, they are all 22 gauge.
is there any way i can get to them wires with out taking the torx screw ???
Posted By: Velocity Motors
Date Posted: October 10, 2009 at 10:31 PM
You DO NOT need to remove the box on these VW's. You can access the wires at the base of the box by cutting into the taped loom of wires. Use a CANSL2 or the iDatalink AL-CA and this will give you all the convenience feature interface wires necessary for alarm & remote start connections.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: mitch0627
Date Posted: October 11, 2009 at 8:53 AM
I'm trying to put a engine start button . Will this still work ??
Posted By: Velocity Motors
Date Posted: October 11, 2009 at 9:24 AM
Yes, it will work. The wires are located after the black box under the steering wheel at the base.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Velocity Motors
Date Posted: October 11, 2009 at 9:28 AM
Wire color is RED / BLACK and the IGNITION is BLACK
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: howie ll
Date Posted: October 11, 2009 at 1:49 PM
Relevant to t&t's comment. what's the problem with the torx screw? If you don't have a t20 driver/bit don't even attempt to work on one of these.
Posted By: mitch0627
Date Posted: October 11, 2009 at 4:58 PM
i do have a t20 -/+ i just dont have one that is small enough to take out the black box under the column... i did it tho and it works 100%
Posted By: Steven Kephart
Date Posted: October 12, 2009 at 1:29 AM
Velocity Motors wrote:
You DO NOT need to remove the box on these VW's. You can access the wires at the base of the box by cutting into the taped loom of wires.
I want to second that recommendation. I found out the hard way on that one. Unfortunately the wires specified above didn't meter as ignition wires on the one I did.
|