2010 mazda 3 with smart key
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=117097
Printed Date: April 27, 2024 at 10:15 AM
Topic: 2010 mazda 3 with smart key
Posted By: blue_16v
Subject: 2010 mazda 3 with smart key
Date Posted: October 19, 2009 at 9:52 PM
anybody here done one of these yet? I do 2- 4 REGULAR Mazda 3's a day........ But the SMART KEY AUTOMATIC Version Has me Hung up.... The Wiring for the most part is the same ( Brake, Park lights, Lock and unlock, Tach, TX, RX ) But there Are some very noticable Differences - ( Ignition, Start, and stop, and the transponder are completey Different ) Anyone successfully Install one of these yet? BTW, I'm using a compustar CM5200, W/ ADS- AL CA Bypass, and followed all the directions and still no start.... ANY INFO WOULD BE GREATLY APRECIATED.....
Replies:
Posted By: Velocity Motors
Date Posted: October 20, 2009 at 7:21 AM
CM5200, what firmware are you using and also are you using the D2D or hardwire ? Is the RS232 port unlocked ?
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: blue_16v
Date Posted: October 20, 2009 at 10:41 AM
Velocity Motors wrote:
CM5200, what firmware are you using and also are you using the D2D or hardwire ? Is the RS232 port unlocked ?
using the most up to date firmware(s) tried both D2D and hard wire, made sure the rs232 port is Unlocked.... anyone have a proper wiring diagram for this car, to get it to remote start?, I dont care If I have to sacrafice a Smartkey, I NEED to GET this working...TIA...
Posted By: Velocity Motors
Date Posted: October 20, 2009 at 6:37 PM
Can you post the wires that you used on the CM5200 and the corresponding wires to the ALCA ? Just want to verify your connections. Also, does the module program properly ?
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: syl20rochon
Date Posted: October 20, 2009 at 9:04 PM
Very important to make sure you wired the right diagram (type), is your car automatic or manual?
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: blue_16v
Date Posted: October 22, 2009 at 12:13 AM
Velocity Motors wrote:
Can you post the wires that you used on the CM5200 and the corresponding wires to the ALCA ? Just want to verify your connections. Also, does the module program properly ?
Checked and all confirmed... I still can't get it to work...wth,... anyone have a wiring diagram to bypass this POS, even if I have to run a wire to everything manually to by pass the push to start..... HELP!!!, TIA
Posted By: racing_bidule
Date Posted: October 22, 2009 at 11:37 PM
Which Firmware/Diagram are you using on this car? Document number? (found on the upper right corner of the pages) I'm suspecting you're not referring to the good instructions, the vehicle is far from being the same as a regular key and all the required remote starter wires are in the BLADE guide ------------- If you fail on your first attempt, at least destroy all evidence you tried!
Posted By: syl20rochon
Date Posted: October 23, 2009 at 6:44 AM
You are right, refer to the Idata link manual, it tells you exactly what to do......
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: metz35
Date Posted: October 23, 2009 at 1:57 PM
blue_16v wrote:
anybody here done one of these yet?
I do 2- 4 REGULAR Mazda 3's a day........
But the SMART KEY AUTOMATIC Version Has me Hung up....
The Wiring for the most part is the same ( Brake, Park lights, Lock and unlock, Tach, TX, RX )
But there Are some very noticable Differences - ( Ignition, Start, and stop, and the transponder are completey Different )
Anyone successfully Install one of these yet?
BTW, I'm using a compustar CM5200, W/ ADS- AL CA Bypass, and followed all the directions and still no start....
ANY INFO WOULD BE GREATLY APRECIATED.....
I use the same exact system as you, but when i look up that vehicle it says to us AL(DL)MA software not AL(DL)CA software
Posted By: Velocity Motors
Date Posted: October 23, 2009 at 3:09 PM
metz35 wrote:
I use the same exact system as you, but when i look up that vehicle it says to us AL(DL)MA software not AL(DL)CA software
The ALDL0-CA is the module he used, but he has yet to tell us what firmware version he used. The ALDL-MA is the firmware name he used but not sure what version it is. ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: metz35
Date Posted: October 23, 2009 at 3:37 PM
oh i would have just used a blade
Posted By: blue_16v
Date Posted: October 24, 2009 at 4:24 AM
Ok so I figured out what I did Wrong,... the Neutral safety wire HAS to be connected.... From the idata link module ... Thanks for all of your suggestions and help....
Posted By: dennis f
Date Posted: January 12, 2010 at 5:37 PM
Is there any difference between a Mazda3 and a Mazdaspeed3 with the push button start?
I did a regular 3 a month ago or so and it was very easy to work with. I have only worked on 1 other push button car, an 08 Camry and that came out nice as well.
Does anyone have any feedback on a Speed3?
Thanks!
-------------
-Dennis
Posted By: dennis f
Date Posted: January 12, 2010 at 5:38 PM
Crap, I forgot to mention, it is a 2010
-------------
-Dennis
Posted By: tedmond
Date Posted: January 13, 2010 at 5:09 PM
the speed and the mazda3 dont differ. the only thing that is differant is the engine and some basic upgrades on interior and audio. The wiring is still the same.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: dennis f
Date Posted: January 14, 2010 at 1:58 PM
tedmond wrote:
the speed and the mazda3 dont differ. the only thing that is differant is the engine and some basic upgrades on interior and audio. The wiring is still the same.
So with the push button, is that used or is the starter wired in a traditional sense? I haven't even looked at the car yet, but I would think with the push button, it would be wired differently then a car that has just a key cylinder.
Thanks for the replay and any clarification on this! ------------- -Dennis
Posted By: tedmond
Date Posted: January 15, 2010 at 5:59 AM
the 3s start by holding the brakes. But with a modules you can achieve the same thing in less time than a traditional remote start. I use the Fortin pieces and they work great for me. ------------- Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
|