2005 mazda tribute remote start add on
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=117137
Printed Date: May 16, 2024 at 4:48 PM
Topic: 2005 mazda tribute remote start add on
Posted By: msgue6193
Subject: 2005 mazda tribute remote start add on
Date Posted: October 21, 2009 at 1:10 PM
I have a Ultra Start add on 1155TL I need to know the best way to add this to my keyless entry system and use the lock to activate the remote start? Do I take the lock door wire from the drivers side kick and connect it to the Starter Activation input on the ultra start?
Replies:
Posted By: Velocity Motors
Date Posted: October 21, 2009 at 6:39 PM
Yes, you take the door LOCK wire ( or the door lock motor wire ) and connect it to the activation wire on the Ultra Start. Program it for a triple or dual pulse activation to start the car. You will also need a bypass module for the PATS.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: msgue6193
Date Posted: October 25, 2009 at 1:12 PM
well the problem is the door lock wire is - and the ultra start activation wire only has a + input. Any help I'm working on it right now. Thanks
Posted By: mikvot
Date Posted: October 25, 2009 at 1:31 PM
| Driver Mtr Lock | | PINK/BLACK | | (REV) | | DRIVER KICK | |
Using this wire will provide a (+) pulse to trigger the remote start.
Posted By: msgue6193
Date Posted: October 25, 2009 at 9:03 PM
I hooked it up to the pink/black in the drivers side kick panel but had no luck I did tap the wire to 12v three times and the car started so I know it works. I will have to retest the wire tomm with my 12volt tested b/c i broke the bulb. The only other problem i'm having is finding the parking lights wire which is suppost to be brown and in the kick panel. Anyone else have a problem finding it?
Posted By: chev104275
Date Posted: October 26, 2009 at 6:29 AM
if its the same as an 05 mariner its going to be in the harness that runs down behind the carpet
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 9:37 AM
chev104275 I assume you mean the parking lights run down under the carpet? I did see a thicker 12 gauge tan wire but I didn't touch it b/c 1. I thought parking lights where thin gauge and 2. it was tan not brown
Posted By: chev104275
Date Posted: October 26, 2009 at 10:57 AM
i know with the mariners there are 2 harnesses in the kick one that has clips to the floor and the other runs down behind the carpet the one you want is down behind the carpet and its a brown not tan i think its a 14-16 ga wire
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 11:51 AM
ok thanks I found it but the main issue is still I need to find a pos input for the remote starter I tried the pink/black trace but I don't get a pos. signal when I hit the lock button on my keyless entry button. Where can I find it that pos input on the lock side?
Posted By: chev104275
Date Posted: October 26, 2009 at 12:38 PM
where are you looking for the wire ? did you try the harness coming from the door it should be a larger wire maybe 14 to 16 ga
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 1:14 PM
chev104275 wrote:
where are you looking for the wire ? did you try the harness coming from the door it should be a larger wire maybe 14 to 16 ga
I'm looking in the drivers side kick panel for the wire. Yes I tried the pink/black at the door harness (must be neg. pulse). I mainly need to find what turns pos when i hit the lock button. I guess the best way is to put the tester on each wire one by one until it turns positive. I was just hoping one of them turns pos at the door harness. I was looking all over the web for a wiring diagram but can't find it?
Posted By: chev104275
Date Posted: October 26, 2009 at 2:03 PM
this is for an 05 mariner but try it should be the same. At the SJB in a brown connector pin 20 should be Pink/Black 16 gauge
there should be one in the door harness it has to go from the Lock relay to the acuator inside the door How are you testing a DMM ?
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 2:27 PM
chev104275 wrote:
this is for an 05 mariner but try it should be the same. At the SJB in a brown connector pin 20 should be Pink/Black 16 gauge
there should be one in the door harness it has to go from the Lock relay to the acuator inside the door How are you testing a DMM ?
I actually haven't connected anything to the SJB I will have to look on the passenger side center console for it. I using a 12v tester light I didn't see a need to break out the mulit meter (guess it is a good Idea for neg wires).
Posted By: chev104275
Date Posted: October 26, 2009 at 3:37 PM
the only wiring diagrams i have are for escape/mariner which should be the same and they show a pink/black running from the SJB into the door to the acuator
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 4:11 PM
chev104275 wrote:
the only wiring diagrams i have are for escape/mariner which should be the same and they show a pink/black running from the SJB into the door to the acuator
I will double check it the pink/black but does it say the wire is (+) or (-) ?
Posted By: chev104275
Date Posted: October 26, 2009 at 4:53 PM
positive lock feed to the acuator
-------------
If i Can't Install it I Don't need it Joe
Posted By: msgue6193
Date Posted: October 26, 2009 at 7:40 PM
chev104275 wrote:
positive lock feed to the acuator
' I tested the pink/black wire going into the door and still no luck no pos. I plan to look at things better when i have more time this weekend. thanks for everyone that helped me. i will post my findings .
|