fortin can sl2 / 2007 nissan maxima
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=117161
Printed Date: May 16, 2025 at 7:30 PM
Topic: fortin can sl2 / 2007 nissan maxima
Posted By: dcman41
Subject: fortin can sl2 / 2007 nissan maxima
Date Posted: October 22, 2009 at 12:47 PM
Hi, i am about to install a fortin can-sl2 into a 2007 nissan maxima with intelli key. But i have a quick question. In the diagram for the intelli key wiring which i posted in this topic, it says make 3 to 4 loops around the ingition barrel. Which wires go around the ignition barrel? Any input on this situation is appreciated thank you. https://www.zshare.net/download/67344610735fece9/ theres the pdf file for the intelli key wiring so you can see what im talking about.
Replies:
Posted By: metz35
Date Posted: October 22, 2009 at 10:49 PM
according to the instructions its BROWN / white and light blue/black
Posted By: Chris Luongo
Date Posted: October 22, 2009 at 11:44 PM
I've done a bunch of those cars and I've never wrapped loops of wire around anything.
Never heard of that site either.
It's possible you're looking at a page of the CAN-SL2's install guide that's supposed to be for a different kind of car. That module covers many different kinds of cars and each has its own type of installation.
Go directly to www.ifar.ca and you can either search by the name of the product, or just click on Vehicles (easier) and put in your car.....when you find the CAN-SL2 there should be a place to click for the install guide.
Each car has an "install type." Be sure that you're looking at the correct type for your car.
Posted By: Velocity Motors
Date Posted: October 23, 2009 at 8:06 AM
Chris is right, the Nissan uses CANBUS to do immobilizer bypass not the ring wraps. You are looking at the Dodge/Chrysler/Jeep installation diagram.
-------------
Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: dcman41
Date Posted: October 23, 2009 at 11:51 AM
Ok, i figured it out, that diagram i posted is completely OPTIONAL to have the ignition barrel unlocked after the remote start
Posted By: metz35
Date Posted: October 23, 2009 at 2:35 PM
no he is right you need a ring for smart key in order to do a take over
Posted By: dcman41
Date Posted: October 23, 2009 at 11:16 PM
Ok, so i will do it so i can do the take over, but that still leaves me with what wires get wrapped around the ignition barrel ?
Posted By: dcman41
Date Posted: October 24, 2009 at 3:18 PM
Also one last question, in that diagram, it looks as if i have to connect to both key sense wires RED / blue + RED / white and diode isolate. My question is which wire off the alarm/remote start would i connect those to ? I looked through the whole manual and none of them are a key sense wire. It shows the keysense wires going to the ignition? What do i do here ? Everything else is pretty much straight forward.
Posted By: Velocity Motors
Date Posted: October 24, 2009 at 9:18 PM
dcman41 wrote:
Ok, so i will do it so i can do the take over, but that still leaves me with what wires get wrapped around the ignition barrel ?
The LIGHT BLUE/BLACK will need to be extended and wrapped aound the ignition column. Attach the end of the LIGHT BLUE/BLACK extended wire to the BROWN / WHITE wire on the 4 pin WHITE connector on the CANSL2 ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: Velocity Motors
Date Posted: October 24, 2009 at 9:20 PM
dcman41 wrote:
Also one last question, in that diagram, it looks as if i have to connect to both key sense wires RED / blue + RED / white and diode isolate. My question is which wire off the alarm/remote start would i connect those to ? I looked through the whole manual and none of them are a key sense wire. It shows the keysense wires going to the ignition? What do i do here ? Everything else is pretty much straight forward.
Wire it to ignition.... it says it right on the diagram.  ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: dcman41
Date Posted: October 24, 2009 at 9:52 PM
So i extend the light blue/black wire, wrap it around the ignition barrel, but then do i take the BROWN / white wire wrap it around the valet key, and then connect the BROWN / white wire to the light blue/black wire ?
Posted By: Velocity Motors
Date Posted: October 24, 2009 at 9:54 PM
Yup, you got it.  ------------- Jeff
Velocity Custom Home Theater
Mobile Audio/Video Specialist
Morden, Manitoba CANADA
Posted By: dcman41
Date Posted: October 26, 2009 at 12:18 PM
Im very impressed with this sl2 module, i definatly wasnt expecting it to work as well as it did. I got it all programmed on the first show, however im having issues with the takeover with the smart key, the car remote starts but wont let me take over when i get in the car, i have to manually press the brake and restart the car. I followed the diagram https://ifar.ca/en/download/1873/can-sl2_nissan_infiniti_intellikey.rev-b.pdf i hooked up and diode isolated both RED / blue key sense wires and hooked them to the ignition wire. Anyone know why it wont let me take over ?
|