viper 5701 remote programming
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=117440
Printed Date: May 14, 2025 at 5:31 PM
Topic: viper 5701 remote programming
Posted By: wgrassie
Subject: viper 5701 remote programming
Date Posted: November 03, 2009 at 10:59 AM
1993 Sentra GXE Hi I installed th Viper 5701 in my 1993 Sentar GXE- experiencing the following issue: Step 3 - Getting into Automatic Transmission Mode for Remote Start Function- - Need to change to Automatic Transmission from default Manual Mode
- When I press and hold the valet switch (per Automatic/Manual Programming) the LED does not flash 3 times (no flashes at all) Siren chirps 3 times (no chirps at all)
- The alarm functions of arm and disarm work - Remote Learn (Default Setup) completed succesfully - alarm sounds etc.
Any help would be appreciated ------------- Thanks for your help
Replies:
Posted By: kgerry
Date Posted: November 03, 2009 at 11:17 AM
are you into menu 3? item 1 i think? these units are a real PITA to program without a Bitwriter.....
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: wgrassie
Date Posted: November 03, 2009 at 1:16 PM
The trouble I am having is accessing menu 3 to change from Manual to Automatic. Any ideas on how I can get into menu 3 Thanks for the reply ------------- Thanks for your help
Posted By: t&t tech
Date Posted: November 03, 2009 at 6:35 PM
Is your door trigger wire connected? It really is simple to program, but everything must be functional first!
Posted By: syl20rochon
Date Posted: November 04, 2009 at 5:54 PM
Door pins need to be connected cause the brain needs to see the door open, then turn ignition on the back off, press the switch until you hear 3 chirps, then release the button then press again and hold, you'll hear 1 chirp...while holding down the switch, press the unlock button on the remote, you'll hear 2 chirps that confirms automatic mode...release the switch and wait 5 to 15 seconds until you hear a long chirp, it mean that you have exited the program mode. You're done. Good luck.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: wgrassie
Date Posted: November 04, 2009 at 8:25 PM
Thanks for the information I will work through your instructions and let you know how it works out. Thanks again ------------- Thanks for your help
Posted By: wgrassie
Date Posted: November 04, 2009 at 8:26 PM
Thanks for helping out- will check the door trigger
-------------
Thanks for your help
Posted By: wgrassie
Date Posted: November 06, 2009 at 2:19 PM
I verified the wiring and worked through your instructions. I was able to enter the programming mode and switch to automatic Transmission from the default of Manual- easy to program once you get have the steps to follow. Remote start will still not engage- Any ideas? Thanks ------------- Thanks for your help
Posted By: kgerry
Date Posted: November 06, 2009 at 4:06 PM
did you ground the NSS wire? do you have the toggle switch plugged in? both are required to allow R/S to engage..... does it try to start? if not, how many light flashes do you get? ------------- Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: wgrassie
Date Posted: November 09, 2009 at 9:37 AM
- When I engage the Remote Start function, I get 1 Parking Light Flash
- After trying to Remote Start- I tried to start the car with the key,
- the car will not start until I toggle the Remote Start switch to the off position.
Any thoughts? Thanks ------------- Thanks for your help
|