95 mercury villager remote start
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=118376
Printed Date: May 05, 2024 at 6:45 PM
Topic: 95 mercury villager remote start
Posted By: pavlik
Subject: 95 mercury villager remote start
Date Posted: December 09, 2009 at 3:00 PM
Hello everyone, I tried to install a remote starter (Prestige) to my Mercury Villager 1995. I have a problem with finding where to connect wire Tach and door lock and unlock. Please help me. ------------- God bless You!
Replies:
Posted By: ckeeler
Date Posted: December 09, 2009 at 4:26 PM
do you own a DMM or can you borrow one from a friend? it is a must to properly identify the correct wires.
Posted By: pavlik
Date Posted: December 09, 2009 at 4:48 PM
I am sorry, but what is a DMM?
-------------
God bless You!
Posted By: ckeeler
Date Posted: December 09, 2009 at 4:56 PM
Digital Multi Meter. its also sometimes called a Digital Volt Meter.
Posted By: pavlik
Date Posted: December 09, 2009 at 5:21 PM
I do have DMM, but how does it help me find the wires that i need to connect lock and unlock?
-------------
God bless You!
Posted By: ckeeler
Date Posted: December 09, 2009 at 5:30 PM
you use it to test the wires while operating the switch so that you know you have the correct wires before you just go and hook into them.
Posted By: pavlik
Date Posted: December 09, 2009 at 5:39 PM
so do I need to pull the wires from remote starter to the door switch?
-------------
God bless You!
Posted By: ckeeler
Date Posted: December 09, 2009 at 5:56 PM
no. look for a GREEN / WHITE and GREEN/ orange wire in the drivers kick panel and then use your DMM to test them to be sure they are the correct wires. if not, keep looking for those colors and keep testing each time until you find them. dont attempt hooking up the door lock outputs from the R/S to any wires you find until you are positive through testing, that you found the correct wires. they are negative trigger.
Posted By: pavlik
Date Posted: December 09, 2009 at 6:15 PM
Thanks, I tried to find them there but there are hundreds of wires and i dont know exactly were to find the wires that lock and unlock. Maybe you can tell me exactly were they are. or give me a link to an image. Wire to tach, do i need to attatch it to to the coil on the engine or can i find another wire under the kick panel ------------- God bless You!
Posted By: ckeeler
Date Posted: December 09, 2009 at 7:10 PM
you may have better luck finding the wires in the kick panel for the locks if you can find the harness from the boor boot coming in, maybe you can even find them in the door boot itself. at any rate you dont need to remove the door panel or anything like that. i would use an injector wire for the tach signal if you are able to get one. all the injectors will have 2 colors with one color being common on them all, use any wire on any injector that is NOT the common color.
Posted By: pavlik
Date Posted: December 09, 2009 at 8:30 PM
can i find the injectors under the dashboard? if yes, where? thanks
-------------
God bless You!
Posted By: ckeeler
Date Posted: December 09, 2009 at 8:35 PM
i've never tried on that year/make/model. i dont think you can. if it's possible, trust me, someone will be along to chime in.
Posted By: pavlik
Date Posted: December 09, 2009 at 9:01 PM
thank you very much, you were very helpful!
-------------
God bless You!
|