avital champion mark ii wiring diagram
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=119545
Printed Date: May 05, 2025 at 10:17 AM
Topic: avital champion mark ii wiring diagram
Posted By: courtland
Subject: avital champion mark ii wiring diagram
Date Posted: January 22, 2010 at 12:56 PM
Just took this out of my 1994 BMW 325i and now (obviously), car won't start. Does anyone have a wiring Schematic for this? Thanks! The back of the box has two paper labels stuck to it: JJ4436F4FB 5250 and AP1734F8, 65250 04727 04728
Replies:
Posted By: Mike M2
Date Posted: January 22, 2010 at 1:56 PM
Removing it won't make the car not start unless you shorted something out and blew a fuse. If it just won't crank, i notice a relay in the picture on the left side. If this relay is a starter kill relay you need to reconnect the two wires the relay was connected to.
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: courtland
Date Posted: January 22, 2010 at 2:14 PM
Mike M2: You are amazing. The Grey wire (Pinout 11 on the 14-pin Connector), is the "Starter Disable Relay Wire" which goes to a Bosch Relay then, two heavier gauge wires out (which, presumable need to be reconnected to close the circuit).
Only a tiny portion of the relay is visable in the Photo which I cannot believe you saw. Anyway, thank you so much. I went on to Who IS and Search Avital.Com and got the owner's Phone number, called them and they emailed me the Install guide for this which contains the Wiring Diagram. How do I post this PDF - the same way I uploaded the Photo from original post? - Regards Courtlad
Posted By: howie ll
Date Posted: January 22, 2010 at 5:28 PM
You're looking for either a light GREEN/ thin black trace wire or it changes to BLACK / YELLOW. rejoin from relay.
Posted By: courtland
Date Posted: January 24, 2010 at 6:42 PM
Rejoined the ignition wire (it was split to accomodate the Avital relay). Engine tries to start but won't. Found out I'm not getting 12vdc at the fuel pump. I pulled the Fuel Pump Relay and put jumper wire in the relay socket and do get 12vdc at pump. So I'm thinking its the fuel pump relay. Stumped for now. Will order new relay.
Posted By: dwheeler0
Date Posted: March 29, 2010 at 1:06 PM
Hi Courtland,
I'm not seeing any reply to your question about posting the install guide and presume that there may be some legal stuff...
Is it possible to receive that pdf.
TIA,
David
wheelerdavidAThotmail.com
Posted By: courtland
Date Posted: March 29, 2010 at 10:44 PM
David:
Being a "Rookie" I am not allowed to upload file attachments. However, I'd be happy to email you the pdf.
Regards
Courtland
prospectofwhitby@gmail.com
Posted By: the12volt
Date Posted: March 29, 2010 at 10:53 PM
courtland wrote:
David:
Being a "Rookie" I am not allowed to upload file attachments. However, I'd be happy to email you the pdf.
Regards
Courtland
prospectofwhitby@gmail.com
You can upload it here: https://www.the12volt.com/addfile/addfile.asp -------------  the12volt • Support the12volt.com
Posted By: courtland
Date Posted: March 29, 2010 at 10:59 PM
Done ! Thank you.
|