viper 5901 on a 2008 toyota camry
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=119616
Printed Date: April 23, 2024 at 4:30 AM
Topic: viper 5901 on a 2008 toyota camry
Posted By: snake212
Subject: viper 5901 on a 2008 toyota camry
Date Posted: January 25, 2010 at 3:50 AM
hello. i installed my car alarm and i wanted some help on a few things and i hope all my question will get answered.
-basically i want my car to chirp with the lock and unlock through the factory camry piezo speaker.
-i want only the signal lights to light up not the parking lights with lock and unlock.
-and also if it is possible to have my high beams light up when the alarm goes off.
Replies:
Posted By: Mike M2
Date Posted: January 25, 2010 at 6:30 AM
1 I'm sure it's possible, look for the piezo and apply power to it from the horn honk wire thru a relay. 2 Signals are the same as hazards, white negative at the switch. If you need turn signals, yellow and green at the fuse box, 12 pin plug, pin 9 and 12(may not be the same plug). 3 I'm sure finding the highbeam wire is simple, you know it's a negative at the light switch... ------------- Mike M2
Tech Manager
CS Dealer Services
Posted By: snake212
Date Posted: January 26, 2010 at 12:35 AM
thanks alot for the help. but from the alarm itself how would i make the high beams go off which wires would give that output?
Posted By: Mike M2
Date Posted: January 26, 2010 at 6:25 AM
If you want them to flash you would use the parking light output, just be sure of polarity. How are your lights connected now? If they are negative you could just tap into them and diode isolate...
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: snake212
Date Posted: January 26, 2010 at 12:29 PM
But wouldn't that make the high beams flash when I lock and unlock the car?
Posted By: kgerry
Date Posted: January 26, 2010 at 12:49 PM
tie it with a relay to your siren output....... but you'll need to program confirmation chirps off, or you'll have the same problem.......
-------------
Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: snake212
Date Posted: January 26, 2010 at 11:20 PM
but that will defeat the purpose of what i was doing. i wanted to have the factory chirp instead of the viper siren as unlock and lock confirmation.
Posted By: kgerry
Date Posted: January 27, 2010 at 9:27 AM
i think the Idata module for that vehicle chirps thru the OE piezo...... ------------- Kevin Gerry
Certified Electronics Technician
MECP First Class Installer
Owner/Installer
Classic Car Audio
since 1979
Posted By: snake212
Date Posted: January 28, 2010 at 1:28 AM
im not really familiar to the idatalink modules.
Posted By: Mike M2
Date Posted: January 28, 2010 at 6:25 AM
kgerry wrote:
i think the Idata module for that vehicle chirps thru the OE piezo......
I don't recall this but it may... ------------- Mike M2
Tech Manager
CS Dealer Services
Posted By: x1le
Date Posted: January 28, 2010 at 9:42 AM
snake212 wrote:
But wouldn't that make the high beams flash when I lock and unlock the car?
What alarm do you have? I know on viper units you can program the parking lights to not flash with lock/unlock
Posted By: snake212
Date Posted: January 28, 2010 at 11:04 PM
i have a viper 5901 alarm. but i still want to keep the light confirmation with lock and unlock without the high beams. i guess its an either or situation unless someone can advise something else.
|