Print Page | Close Window

4runner viper 5701

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=119989
Printed Date: June 15, 2024 at 8:50 PM


Topic: 4runner viper 5701

Posted By: nealdeacon
Subject: 4runner viper 5701
Date Posted: February 08, 2010 at 8:51 PM

Hello, I would like to use the remote start portion of the viper 5701 only. Using fortin sl2 module. What wires get used? Does anyone have info on 08 4runner?  Thanks much.



-------------
ou812



Replies:

Posted By: monty_77
Date Posted: February 09, 2010 at 12:21 AM
Toyota 4Runner 2008

WIRE        COLOR        LOCATION    POL.
Battery 1 WHITE/ Blue Ignition Harness Positive
Battery 2 Red Ignition Harness Positive
Ignition 1 BLACK/ Red Ignition Harness Positive
Ignition 2 Blue / YELLOW Ignition Harness Positive
Starter 1 GREEN/ Black Ignition Harness Positive
Accessory 1 WHITE/ Green Ignition Harness Positive
Parklights Positive Green Trailer Connector Above Driver's Kick Panel Positive
Parklights Negative Green At BECU Behind Fuse Box top Connector Negative
Brake Lights GREEN/ YELLOW Trailer Connector Above Driver's Kick Panel Positive
Horn GREEN/ Red Right Of Steering Column Gray Connector Negative
Tach BLACK/ Orange (6) Above Gaz Pedal At The Top Blue Connector
Lock Blue/White Driver's Kick Panel Door Harness 18 Pins Conn. Negative
Unlock Blue/Orange (2) Driver's Kick Panel Door Harness 18 Pins Conn. Negative
Trunk Same as Unlock
Driver Door Unlock Green Driver's Kick Panel Door Harness 18 Pins Conn. Negative
E-Brake Lt.Green At BECU Behind Fuse Box Middle Connector Negative
OEM Hood Switch Pink/Green Driver Kick Panel In A Blue Connector Negative
Disarm Green (3) Driver's Kick Panel Door Harness 18 Pins Conn (1) Negative
Rearming Blue (4) Driver's Kick Panel Door Harness 18 Pins Conn. Negative
Trunk Pin GREEN/ YELLOW Back Door ECU, Left Side Of Liftgate. Negative
KeySense GREEN/ YELLOW At Key Switch In A 4 Pins Connector Negative
Door Pin FL RED / Black At BECU Behind Fuse Box Middle Conn. Pin 23 Negative
Door Pin RL Pink/Black At BECU Behind Fuse Box Middle Conn. Pin 11 Negative
Door Pin FR RED / Yellow At BECU Behind Fuse Box Middle Conn. Pin 12 Negative
Door Pin RR Pink/Blue At BECU Behind Fuse Box Middle Conn. Pin 24 Negative
Rear Defogger GREEN/ Red At BECU Behind Fuse Box Middle Conn. Pin 1 Negative
VSS PURPLE / Red ECM Behind The Glove Box AC
Head Lights RED / White At BECU Behind Fuse Box top Connector Negative
Auto lights OFF GREEN/ Orange At BECU Behind Fuse Box top Connector Open
Windows Roll Up Yellow/Red + BLACK / YELLOW At BECU Behind Fuse Box Middle Conn (5)
Windows Roll Down BLACK/ Blue + BLACK / YELLOW At BECU Behind Fuse Box Middle Conn (5)
Moon Roof Tilt Gray At Roof Console Neagtive
Moon Roof Open Lt.Green At Roof Console Neagtive
Moon Roof Close Gray At Roof Console Neagtive
Wiper Protection Blue At Wiper Switch Open
BackUp Lights RED / Yellow At Connector Left Side Of Fuse Box Positive
Transponder RX Pink/Green At Transponder Connector Pin 6 Data
Transponder TX Lt.GREEN/ Red At Transponder Connector Pin 5 Data

Comments :
NOTE:This vehicle is equipped with a IMMOBILIZER passive anti-theft system.
(1) To Disarm for Remote Start, send a ground while running on the keysensor wire, that will Disarm.
(2) Need to pulse the WHITE/ Red (-) at the same time for Child Safety Lock Override.
(3) First Pulse will Disarm Factory Alarm and Unlock Drivers Door. Second one will Unlock all Doors.
(4) This wire will Lock all doors and Arm the Factory Alarm System.
(5) To roll down the window, close contact between the BLACK/ Blue & BLACK / YELLOW, To roll up close contact between Yellow/Red and BLACK / YELLOW.
(6) On some 4Runner, the tach signal is on a BLACK/ White above the BLACK/ Orange in the same Blue connector




Posted By: nealdeacon
Date Posted: February 09, 2010 at 2:02 PM
This is a massive help. I owe you one. Thanks alot!!!!!!!

-------------
ou812




Posted By: monty_77
Date Posted: February 09, 2010 at 4:59 PM
your welcome and

check your pm's




Posted By: nealdeacon
Date Posted: February 09, 2010 at 6:32 PM
Also, will derected techs provide vehicle specific wiring diagrams for this alarm?  I was hoping they would. What I could really use is a specific diagram for which wires go where, is it just a t tap or cut and splice. any help? thanks much

-------------
ou812




Posted By: monty_77
Date Posted: February 09, 2010 at 6:35 PM
solder everything, only way to go

i doubt that directed will give you any help with wireing if you are not a dealer




Posted By: nealdeacon
Date Posted: February 09, 2010 at 6:56 PM
I am not a dealer, thats the problem, and I always solder and shrink wrap where I can. A portasol makes things alittle easier. Any pics would be great.

-------------
ou812




Posted By: Mike M2
Date Posted: February 09, 2010 at 9:18 PM
Be advised the factory remotes are not going to work whenever you remote start this truck. You will have to use a key in the door. You may consider connecting the keyless wires on the 5701...

-------------
Mike M2
Tech Manager
CS Dealer Services




Posted By: monty_77
Date Posted: February 09, 2010 at 10:47 PM
there is a lot of help here. And i would say more knowledge about doing remotes starts and alarms than even DEI has on hand

so don't be afraid to ask




Posted By: tedmond
Date Posted: February 10, 2010 at 7:36 AM

agreed with monty.

DEI doesnt know all the problems and questions real DIY people have.

the can-sl2 will do the door locks for you through CANBUS.

if you need a wiring diagram, if you purchased your CANSL2 at a store, look for a small card (size of credic card), go to www.wirecolour.ifar.ca and type in the serial number for your car. Only selected bypasses have those, but if your a dealer you get infinate number of them.



-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert




Posted By: nealdeacon
Date Posted: February 10, 2010 at 5:16 PM
You guys rock. I would like  to usw the viper 5701 remotes to control the keyless entry and remote start. However, I would like the toyota factory security to remain. I know I can do this and only use the viper remotes. I dont want to carry two remotes around. Thanks Neal

-------------
ou812




Posted By: resquchas
Date Posted: December 21, 2010 at 10:48 PM
a little more detail on the wiring diagram.

park lights +
foot brake + both of these wires are found in a white plug taped up if not in use somewhat above and behind the fuse box close to where the driver door grommet starts.

key sense - blue connector on bottom of steering column
tach    check frequency   blue plug on top left side at the right side of steering column
horn      - grey connector bottom left side of the right side of steering column.




Posted By: zerepdivad
Date Posted: December 21, 2010 at 11:00 PM
tach on most newer yotas, and lexus' can be also had at the obd2 port, usually in the corner either black or BLACK/ white.
On most cars parking lights, and brake lights can be found in the kick harness goign to the rear of the car as well. or obviously at the switches.

-------------
A DMM is a beautiful thing.

MECP Advanced Installer Certified.





Print Page | Close Window