viper 5901 2006 accord dlpk
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=120190
Printed Date: May 15, 2024 at 8:05 PM
Topic: viper 5901 2006 accord dlpk
Posted By: p-wi
Subject: viper 5901 2006 accord dlpk
Date Posted: February 17, 2010 at 8:19 AM
so im just starting this install and wanted to make sure i understood all the connections. as i laid out all the wires and looked at the installation instructions i instantly became overwhelmed and now need serious mental help.
bit of background i understand diodes, have hooked up relays, one remote start/alarm install previous.
so: exactly what wires do i need from the ignition switch harness?
also im on a bit of a time restraint so to make it easy can a knowledgeable person look at my instructions and tell me hook this wire to that and this to that and now your done?
thanks in adavance!
Replies:
Posted By: dman007
Date Posted: February 17, 2010 at 9:58 AM
From the ignition harness, you will need 12volt constant - WHITE Ignition 1 - BLACK / YELLOW Ignition 2 - BLACK/ RED Accessory - BLACK/ RED Starter - BLACK/ WHITE Remember all of these wires will be heavier gauge, coming directly from key clyinder wiring harness. ------------- DTS Performance
St Petersburg, FL
Posted By: p-wi
Date Posted: February 17, 2010 at 10:25 AM
what wires do those hook up to on the 5901 harness
Posted By: x1le
Date Posted: February 17, 2010 at 10:47 AM
dman007 wrote:
From the ignition harness, you will need
12volt constant - WHITE _ connect to red, redwhite, and redblack
Ignition 1 - BLACK / YELLOW _ connect to pink
Ignition 2 - BLACK/ RED _ connect to pink/white
Accessory - BLACK/ RED _ connect to orange
Starter - BLACK/ WHITE _ cut wire in half and connect the car side to purple and the key side to green
Remember all of these wires will be heavier gauge, coming directly from key clyinder wiring harness.
don't forget to verify wire color accuracy with a meter prior to connecting.
Posted By: dasbogie
Date Posted: February 17, 2010 at 10:54 AM
Do you have ac bypass for the transponder? the dlpk does door locks, factory alarm disarm, trunk pop, triggers but not the chipped key
Posted By: p-wi
Date Posted: February 17, 2010 at 11:14 AM
i was told that the dlpk had a immobilizer bypass and it connected directly to the 5901 just needed 2 additional wires.
is the accessory supposed to be WHITE/ RED_ORANGE????
Posted By: p-wi
Date Posted: February 18, 2010 at 5:42 PM
does anyone know where the orange on the 5901 connects to? white and red?
Posted By: dasbogie
Date Posted: February 18, 2010 at 8:37 PM
did you test that wire with a meter in all key positions?
Posted By: p-wi
Date Posted: February 18, 2010 at 8:41 PM
what am i testing for volts i assume but what indication in each position, and what is the orange wire supposed to be connection to ?
Posted By: x1le
Date Posted: February 18, 2010 at 8:43 PM
p-wi] wrote:
what am i testing for volts i assume but what indication in each position, and what is the orange wire supposed to be connection to ?
|