keyless entry, 2008 pontiac g6

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=120287
Printed Date: July 05, 2025 at 11:18 AM

Topic: keyless entry, 2008 pontiac g6

Posted By: nbkg7e9
Subject: keyless entry, 2008 pontiac g6
Date Posted: February 21, 2010 at 4:12 PM

Purchased keyless entry to Pontiac g6 2008 w/o keyless entry with power door switch.

After review installation manual. Not sure if I can do it.

Open the fuse box in driver’s side compartment, the wire is in a block with fuse on one side and wires in hole of block.

Anybody have an easy approach how to id wires.

Thank You

-------------
larry

Replies:

Posted By: tommy...
Date Posted: February 21, 2010 at 5:31 PM

	Power Unlock		WHITE		(-)		AT BCM MODULE BEHIND TRIM AT FRONT OF CENTER CONSOLE ON PASSENGER SIDE	...	*
	PowerLock		WHITE		(-)		AT BCM MODULE BEHIND TRIM AT FRONT OF CENTER CONSOLE ON PASSENGER SIDE		...**

Here's a schematic for the locks...Relays may not be needed depending on UNIT>>>? https://documents.audiovox.com/700649.pdf

*..........PIN #66 - TAN PLUG, USES 1.5K RESISTOR TO GROUND TO TRIGGER UNLOCK

**.........PIN #66 - TAN PLUG - USES STRAIGHT GROUND TO TRIGGER LOCK

And a Meter...! What keyless entry unit did you buy(make and model #)...Here's the power connections too...

Battery		RED / WHITE		(+)		IGNITION SWITCH HARNESS
	Ignition 1		PINK		(+)		IGNITION SWITCH HARNESS

-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!

Posted By: nbkg7e9
Date Posted: February 21, 2010 at 6:42 PM

Bulldog ke1702

Thanks

-------------
larry

Posted By: kreg357
Date Posted: February 21, 2010 at 7:20 PM

Follow the KE1702 instructions for a Type B (-) door lock system. Go to Radio Shack and buy a 1500 ohm resister and use the Bulldog instructions for you cars door locks : https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp at the bottom of the page. The White wire in your car is found with the above listed info from Tommy.

Good luck.

-------------
Soldering is fun!

Posted By: kreg357
Date Posted: February 21, 2010 at 7:36 PM

If you have a Factory alarm on the car you might have to hook up the FASD wire.

Additionally you can hook up the Parking Light (-) output to the car to flash the lights on lock & unlock.

And if you have an electric trunk pop switch in the car you can attach that wire also to allow remote control of the trunk release.

You will need a Digital Multi- Meter to help you safely locate the correct wires.

Bulldog Security web site has the cars wiring and their Tech Support is pretty good ( expect to be on hold for a while ).

https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp

-------------
Soldering is fun!

Posted By: tommy...
Date Posted: February 21, 2010 at 8:28 PM

So both the lock/unlock wires from the keyless unit will attach to this White wire in car...Then the 1500 ohm resistor will be placed on the end of the unlock wire of the keyless unit before you connect it...!

-------------
M.E.C.P & First-Class
Go slow and drink lots of water...Procrastinators' Unite...Tomorrow!