2004 rav4, viper 5701
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=120973
Printed Date: May 03, 2024 at 1:51 AM
Topic: 2004 rav4, viper 5701
Posted By: ltrains
Subject: 2004 rav4, viper 5701
Date Posted: March 25, 2010 at 9:19 PM
i was wondering if i have to buy the bypass unit for the factory alarm, whats the benefits of buying the bypass to keep the factory alarm.
where is a good place to place the brain? thanks a lot guys,
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Replies:
Posted By: tedmond
Date Posted: March 26, 2010 at 5:31 AM
you need a bypass to allow it to start. it doesnt have much to do with your factory alarm. the ne wunit you are puttin in will control your factory alarm. a good place is any where high up in the dash. ------------- Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: Mike M2
Date Posted: March 26, 2010 at 4:41 PM
There is no factory alarm in this truck. There may be a dealer installed Toyota alarm tho...
-------------
Mike M2
Tech Manager
CS Dealer Services
Posted By: ltrains
Date Posted: April 14, 2010 at 4:31 PM
Hey everyone, i need some help. i just finshed installing the viper 5701 on my 2004 toyota rav4. the thing is when i first plug the battery terminal back in, the alarm tries to cranks the car continously but the doesn't start fully. i can't find the problem.
PLEASE Help, thanks you
i followed the wiring diagram.
The viper has 9 wires
h3 pink ignition 1 connected to black
h3 2 RED / white ignition2 connected to blk / YELLOW
h3 3 orange accessory connected blue/red
h3 4 violet starter output connected to red on near the key
h3 5 green start input connected to red away from the key
h3 6 red ignition 1 relay
h3 7 pink/white igition 2 relay
h3 8 pink blk ignition 2 flex relay
h3 9 blk/red accessory/starter relay
12 VOLT CONSTANT WHITE (+) and BLACK/ RED (+) IGNITION SWITCH HARNESS
STARTER RED (+) IGNITION SWITCH HARNESS
IGNITION 1 BLACK (+) IGNITION SWITCH HARNESS
IGNITION 2 BLACK / YELLOW (+) IGNITION SWITCH HARNESS
IGNITION 3 N/A
ACCESSORY /HEATER BLOWER 1 BLUE/RED (+) IGNITION SWITCH HARNESS
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: ltrains
Date Posted: April 14, 2010 at 6:19 PM
any help please,! thank you
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: Chris Luongo
Date Posted: April 14, 2010 at 6:41 PM
Red, RED / white, and RED / black......... I'm pretty sure you're supposed to have all of those connected to a constant power source. If you have any of those connected to the car's ignition wires it's probably going to do all sorts of unpredictable things.
Sounds like the purple and green starter wires are backwards as well. Green goes to the key side of the factory wire you cut, and purple goes to the side that goes to the starter side.
Pink should be connected to the black Ignition 1 on the car
Pink/white should be connected to the thick BLACK / YELLOW Ignition 2 on the car.
Orange could be connected to the RED / blue accessory wire on the car, but this connection is not necessary.
Posted By: ltrains
Date Posted: April 14, 2010 at 7:08 PM
h3 7 pink/white igition 2 flex relay output
h3 8 pink blk ignition 2 flex relay
are these left unwired? thank you so much!!
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: ltrains
Date Posted: April 15, 2010 at 9:57 AM
oh man, my car keep continuously starting.
i put Red, RED / white, and RED / black on the constant BLACK/ red wire.
pink ignition 1 connected to black
accessory is not wired
violet starter output connected to red wire on away the key
green start input connected to red wireaway near the key
pink blk ignition 2 flex relay is unwired.
i dont wants going on. i'm thinking starter output and input is not good. how far away starter output from key should it be?
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: ltrains
Date Posted: April 15, 2010 at 12:56 PM
help please, now my car idles low at .50 rpm. what should i do.
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: ltrains
Date Posted: April 16, 2010 at 10:48 AM
the red start i cutted, green goin near the key, the one left hanging is goin connect with the purple. but remote start still doesn't work.
but if i connected the purple one the red wire after the plug. it starts continously. please help ------------- grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
Posted By: tedmond
Date Posted: April 16, 2010 at 5:54 PM
is that a scotchlock i see? if so remove it and solder the wires. ------------- Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: ltrains
Date Posted: May 05, 2010 at 8:54 AM
any help please
-------------
grand cherokee 97 4.0
avic n2 with cdr11 remote and xm..
|