Has anyone programed an aps996?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=12117
Printed Date: September 08, 2025 at 2:43 AM
Topic: Has anyone programed an aps996?
Posted By: 1funkycat
Subject: Has anyone programed an aps996?
Date Posted: April 12, 2003 at 3:11 PM
Hi,
Has anyone installed/ programed an audiovox aps996 alarm before? Is there a trick to get the alarm to recognize the vehicles tach? I've behen over the wireing 20 or so times and i have preformed te programming steps word for word. I still have'nt tried banging my head on the fender, but am very close. Please Help!
Replies:
Posted By: Chris Luongo
Date Posted: April 12, 2003 at 3:18 PM
Are you doing it this way?:
1. Ignition on.
2. press and relase switch three times (siren chirps)
3. Ignition off. (siren makes long chirp)
4. Push and HOLD switch, start engine.
5. Parking lights flash on and off---let them flash maybe ten times, then release switch. Lights will come on steady, then go out after three seconds.
If you're not getting the siren chirps at all, you might have the thick blue ignition wire hooked up incorrectly.
If the chirps work, but the parking lights don't flash when you start the engine, you probably have the wrong tach wire, or a bad connection.
There is a very simple way to test your connection, without taking things apart. Just go right to the alarm brain, and put your test probe right to the GREEN/ orange wire at the brain...if it tests correctly there, you have the right wire.
Also, you didn't bother to mention what kind of car it is, but what is it? That way we can verify you have the right wire.
Posted By: 1funkycat
Date Posted: April 12, 2003 at 3:27 PM
The car is a 95 grand cherokee. The tach wire should be the grey/white one.
When i shut the ignition off(step3) I get two chirps not 1 long one.
I have tested the GREEN/ orange wire at the plug on the harness and it did have a strong signal.
Posted By: Chris Luongo
Date Posted: April 13, 2003 at 8:54 AM
I don't know why the alarm would make two short chirps instead of one long one---that's odd.
It still might be a good idea to make sure that the thick blue ignition wire is hooked up correctly---if you test it at the brain, it should show power when the key is in the Run and Start positions.
Also, the information I have shows tach as gray/blue at the PCM, so possibly you still have the wrong tach wire.
What are you using to test for tach......is it an analog meter by chance? I found that if you set an analog meter to AC, and touch the meter to a 12-volt DC source like a car battery, the analog meter still shows around 7 volts AC, which can create confusion.
Another thing to do is to use one of the fuel injectors on top of the engine. They're all there in a row, and I believe they will all have one GREEN/ orange wire, and the other wire will be different for each injector........use the color that is always different for tach, and see how it works.
| ITEM | WIRE COLOR |POL| WIRE LOCATION |
| 12V|pink/blk or RED / wht |+ |steering column |
| STARTER|yellow/blue (small) |+ |steering column |
| IGNITION|blue/gray |+ |steering column |
| ACCESSORY|ORANGE / black |+ |steering column |
| POWER LOCK|ORANGE / purple |+ |blk conn. drivers kick |
| POWER UNLOCK|pink/purple |+ |or red conn. pass kick |
| PARKING LIGHTS +|blue/red | |left of st. column |
| HEADLIGHTS|tan/black |+ |at switch-high and low |
| DOOR TRIGGER|yellow *2 |- |drivers kick panel |
| TRUNK/HATCH PIN|tied in with doors |- |drivers kick panel |
| HOOD PIN|BROWN / tan |- |pass. kick blue plug |
| FCTRY ALARM ARM|pink/orange |+ |pass. kick red plug |
|FCTRY ALRM DISARM|purple / YELLOW |- |driver kick black plug |
| TACHOMETER|gray/blue *1 | |powertrain control mod |
| BRAKE WIRE|white |+ |left of brake pedal |
| HORN TRIGGER|gray/orange |- |steering column |
| WIPERS|BROWN / white |+ |steering column |
| LF WINDOW UP/DN|white - lt. blue |A |drivers window switch |
| RF WINDOW UP/DN|brn/wht - pur/wht |A |drivers switch or kick panel|
| LR WINDOW UP/DN|blu/wht - RED / blk |A |drivers switch or kick panel|
| RR WINDOW UP/DN|gry/blk - grn/wht |A |drivers switch or kick panel|
Notes:
*1 High on passenger side firewall under hood. *2 Not underdash light
Posted By: shawoo
Date Posted: April 14, 2003 at 5:22 PM
i have the 995C, which is the 996. Not sure what kind of programming you are trying tod o...but after calling their tech support, i was able to programm my user select chirps from the transmitter. turn ignition on push valet button 3 times turn ignition off then TURN THE IGNITION BACK ON from this point you are in "step" #1...so if you are trying to program the 12th step, you would hit the valet buttons 11 times after that. hope this helped!
|