96 eclipse viper 5901 remote start error
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=121958
Printed Date: May 08, 2024 at 4:38 PM
Topic: 96 eclipse viper 5901 remote start error
Posted By: freakingbori617
Subject: 96 eclipse viper 5901 remote start error
Date Posted: May 22, 2010 at 9:15 PM
ok guys so i did my first alarm install. Time consuming but i wired everything up. The alarm works perfect. No problems but the remote start shows error. I wired the neutral safety wire to the ebrake.
Below is how I wired the remote start harness from the alarm to my ignition harness.I just noticed that my battery is draining slowly.
(H3) 10-pin connector
H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT =BLACK/ White ignition harness
H3/2 RED / WHITE (+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87 = White ignition harness
H3/3 ORANGE (+) ACCESSORY OUTPUT = Blue
H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL) = BLACK/ Red Ignition Switch Harness
H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE) = BLACK/ Red Ignition Switch Harness
H3/6 RED (+) FUSED (30A) IGNITION 1 INPUT = White ignition harness
H3/7 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT = Blue/Black ignition harness
H3/8 PINK/BLACK (+) FLEX RELAY INPUT 87A key side (if required) of FLEX
RELAY = Cut short and tape off
H3/9 RED / BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT = White ignition harness
Replies:
Posted By: smokeman1
Date Posted: May 22, 2010 at 9:42 PM
So what error is it showing?
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: freakingbori617
Date Posted: May 22, 2010 at 9:50 PM
It gives me 7 parking light flashes
Posted By: smokeman1
Date Posted: May 22, 2010 at 10:03 PM
Is your car manual or Automatic? Seven parking lights flashes indicate:
Manual transmission mode is enabled and not initialized.
Page 57 of the Installation Manual
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: freakingbori617
Date Posted: May 22, 2010 at 10:10 PM
yes my car is manual. That is the error showing up. But i have the switch pluged to the brain. The neutral safety wire is connected to the E-brake.
Posted By: mikvot
Date Posted: May 22, 2010 at 10:34 PM
I don't do DEI stuff, but any of the other manny tranny stuff that I install requires a process that you have to go through before you get out of the vehicle. You can't just hop out of the vehicle like you can with a remote start on an auto.
Posted By: smokeman1
Date Posted: May 22, 2010 at 10:38 PM
I have not done a manual remote start install so I must confess that I am not sure of the next step to take. However, in comparing the install manuals for the Viper 5301 and 5701 there is a there is a manual start procedure listed in those manuals that I don't see in the 5901 manual. On page 60 of the 5301 manual and page 78 of the 5701 manual. I don't see this procedure listed at all in the 5901 manual. The 5301 & 5701 install manuals are in the download section of this site, as follows:
Manual transmission remote start
If the vehicle has manual transmission the proper steps must be followed before
leaving the parked vehicle or the remote start feature is disabled.
Make sure the doors on the vehicle are closed.
Put the transmission in neutral.
Press on the brake in the vehicle.
Apply the emergency brake.
Release the brake.
Within 15 seconds activate the remote start from the remote.
The parking lights will flash confirming that the remote start is active.
Turn off the ignition (the car should stay running when key is turned off).
Exit the vehicle.
Arm the alarm (the vehicle should shut off when arming the system).
You can now remote start the vehicle. If a door is opened or if the alarm is triggered before the next remote start activation the system will not remote start. Hope this will work for you.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: freakingbori617
Date Posted: May 23, 2010 at 5:25 AM
No luck guys. I tried exacly those steps and nothing. I also tried setting it in automatic mode but it doesnt seem it went into affect.I've been working on this for about four days to the point i want to pull my hair out. Can someone check the way i wired the remote start up and comfirm it is correct.
Posted By: dasbogie
Date Posted: May 23, 2010 at 7:44 AM
do you have a door pin wire from the viper connected to the car? it needs to see the door trigger before you shut it down.
-------------
Advanced
Posted By: dasbogie
Date Posted: May 23, 2010 at 8:05 AM
also, i believe you have to run a tach wire in manual mode as well. make sure you program the tach first. then go through the shutdown sequence
-------------
Advanced
Posted By: freakingbori617
Date Posted: May 23, 2010 at 8:15 AM
yes the door pin is connected. And the tach wire is connected and used the control center to program tach. I had the starter input and output backwards so i fixed that. But now once i start my car with my key the starter wont disengage.So the remote start wiring must be wrong on something i just cant figure it out
Posted By: smokeman1
Date Posted: May 23, 2010 at 8:42 AM
Looking back on your first post, it looks like you might have the H3/3 wire and the H3/7 wire reversed. The wiriing charts list the BLUE/BLACK as Accessory, and the BLUE as Ignition 2. Also do you have the H3/7 programed as Ignition 2?
H3/7 PINK/WHITE – Ignition 2 flex relay output.
This wire is factory programmed as Ignition 2 and can be programmed as a 2nd accessory or 2nd starter.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: dasbogie
Date Posted: May 23, 2010 at 3:14 PM
since this is a manual how did you bypass the clutch? does it need to be pressed to the floor to start the vehicle with the key?
-------------
Advanced
Posted By: freakingbori617
Date Posted: May 23, 2010 at 4:41 PM
That wiring diagram is wrong the blue wire is acc and the blue black is the 2nd ignition. I have checked myself.I corrected the battery drain it had nothing to do with the install. I removed the clutch switch completely so i can start the veichle without pressing the clutch pedal. Im really fustrated i have check my wiring atleast 6 times and im sure its correct. Is there a way to switch it to automatic mode instead of manual?
Posted By: t&t tech
Date Posted: May 23, 2010 at 7:03 PM
Yes! But we cannot tell you how! t's against fourum rules! Do it by the book!
-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
|