Hi guys I am at a loss I am installing a viper 5900/5301v into a 2003 mountaineer the accesories added to the system are 506t glass sensor and xk05 xpreesskit bypass pre programed by autopreservers .I also have relays set up for (gem wakeup , trunk release, factory disarm ,horn,and dome)
So heres whats happening when I apply power to the system the horn honks once other than thats all it does the blue led does not light up and the siren does not chirp the remote indicates that it is recieving signal via 3 vibrations but nothing actualy happens does not lock/unlock remote start or trunk pop. however i am able to start vehicle and operate lock/unlock trunk pop with factory remote.The light on the xk05 stays constant and wont program keys I tested valet button its working, I dont have a bitwriter yet so I cant scan.PLEASE HELP
wire connections made
harness 1
h-1-1 RED / wht to trunk relay
h-1-2 red to12v+
h1-3 brown to siren red
h-1-4 empty
h-1-5 black to ground
h-1-6 violet to door trigger + blk/blu
h-1-7 blu --not connected
h-1-8 grn--not connected
h-1-9 blk/wht to dome relay out to blk/blu
h-1-10 wht/blu-- not connected
h-1-11 wht to park lights + brown
h-1-12 orange not connected
harness 2
h-2-1 lt blu--not connected
h-2-2 wht/blk--not connected
h-2-3 violet/blk--not connected
h-2-4 grn/wht--not connected
h-2-5 grey/blk--not connected
h-2-6 lt grn/blk to factory disarm relay to GREEN/ violet
harness 3
h-3-1 blk/wht to nuetral safety wht/red
h-3-2 violet/wht to tach tan / YELLOW
h-3-3 brown to + brake brown
h-3-4 grey to hood pin switch
h-3-5 blu/wht not connected
harness 4
h-4-1 ORANGE / blk not connected
h-4-2 brown to horn relay to yellow/lt green
xk05
brown to blu ribbon status
violet rx to grey/orange
orange tx to wht/green
red to 12v +
blk to ground
506t
wired through provided harness through shock sensor
door lock harness
pin 1 lt blu to - unlock
pin 2 empty
pin 3 green to - lock
remote start ribbon harness plugged into xcrs 500m
pin 7 on ribbon cable blue (-) 200 mA STATUS OUTPUT is conected to brown wire on xk05 xpresskit
xcrs 500m
4 of the wires on the 500m were soldered in the wrong pinouts I researched this and found to go by pin digram not color these were switched to correct locations
Sorry 2003 murcury mountianeer v8 factory alarm also arms/disarms
With just power and ground applied to the system, and the antenna plugged in ....... you should be able to get the system and LED to respond. The horn should not honk when you power the system up.
Are you sure you have a good system ground, and power source? Where is your system grounded?
I found out this morning that when i unplugged the 500m the alarm started to work I guess the going by the pin as I read may not of been the solution I guess i'll order another .Door triGgers work ,arms,disarms ,trunk pops ,glass sense works and vehicle still cranks even with 500m not plugged in to module but still has power so I have lost nothing in the vehicle, gained security,and can wait for the remote start thank you for time looking at this to help a stranger I really appreciate it.I'll update on this thread when i recieve new part if I have problems. thanks again
Specify (I unplugged the remote start ribbon harness only) for anyone with the same problem .