viper 5901 lc3 in a 94 civic

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=122477
Printed Date: September 19, 2025 at 5:20 PM

Topic: viper 5901 lc3 in a 94 civic

Posted By: nbboy7
Subject: viper 5901 lc3 in a 94 civic
Date Posted: June 29, 2010 at 5:11 PM

Ok i have everything hooked up but the heavy set wires. I have no clue how to hook them up to the car. The instructions are confusing me. Can anyone tell me tell me what colors of the alarm wires go to colors in the car please. Thanks

Replies:

Posted By: tedmond
Date Posted: June 29, 2010 at 5:34 PM

pull up a wiring diagram, then test your wires.

the output wires on the viper simply go to the wires at the ignition.

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: t&t tech
Date Posted: June 30, 2010 at 6:13 AM

1994 Honda Civic Alarm, Remote Starter, Keyless Entry Wiring Information
Constant 12V+	White	Ignition Switch Harness
Starter	BLACK/ White	Ignition Switch Harness
Ignition	BLACK / YELLOW	Ignition Switch Harness
Accessory	Yellow	Ignition Switch Harness
Tach	Blue	Distributor
Brake Switch	GREEN / WHITE	Brake Switch
Trunk Pin	GREEN/ Black (-)	Above Fuse Panel Blue Connector
Parking Lights	RED / Black	Fuse Panel or Driver's Kick Panel
Head Lamp	RED / White	Steering Column
Hood Pin	n/a
Door Trigger	Light GREEN/ Red (-)	Driver's Running Board One of Two Wires
Door Lock	GREEN / WHITE (-)	2 Pin Connector TapeD to Blue Connector behind Fuse Panel
Door Unlock	GREEN/ Red (-)
Horn Wire	Blue (-)	Steering Column, use Relay
Windows Up	LF=RED / Blue, RF=Blue / YELLOW
Windows Down	LF=RED / Yellow, RF=Blue/Green

-------------

Posted By: nbboy7
Date Posted: July 01, 2010 at 8:05 PM

I dont know where some of them go. Some of the viper wire say in/out put. Then the flex relay wires is geting me confused. So far i have the starter wires and the accessory output on. The rest I'm confused about and i need my car.

H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT

H3/2 RED / WHITE (+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87

H3/3 ORANGE (+) ACCESSORY OUTPUT

H3/4 VIOLET (+) STARTER OUTPUT (CAR SIDE OF THE STARTER KILL)

H3/5 GREEN (+) STARTER INPUT (KEY SIDE OF THE STARTER KILL WIRE)

H3/6 RED (+) FUSED (30A) IGNITION 1 INPUT

H3/7 PINK/WHITE (+) IGNITION 2 / FLEX RELAY OUTPUT

H3/8 PINK/BLACK (+) FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY

H3/9 RED / BLACK (+) FUSED (30A) ACCESSORY/STARTER INPUT

Posted By: smokeman1
Date Posted: July 01, 2010 at 9:27 PM

On your Heavy Gauge Harness, Refer to the Wiring Chart posted from t&t tech, use a DMM to test and verify the wires you will be using

The Red (H3/6) and RED / Black (H3/9) should go to the White. Constant 12 volts. You could also attach the Red (H1/2) wire there.

The Pink (H3/1 to the BLACK / YELLOW

The Orange (H3/3) to the Yellow

The Starter wire BLACK/ White will get cut and connected as: The Violet (H3/4) to the starter side of that wire and the Green (H3/5) to the key side of the starter wire.

The (H3/2) RED / White, (H3/7) Pink/White, and the (H3/8) Pink/Black) will not be needed. Fold them up and tuck them away.

Solder those connections. Good Luck.

-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation