2006 mustang, viper 5902
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=122871
Printed Date: July 09, 2025 at 7:32 PM
Topic: 2006 mustang, viper 5902
Posted By: nuclearmuscle52
Subject: 2006 mustang, viper 5902
Date Posted: July 28, 2010 at 3:45 PM
Hello and thanks in advance.
I have the 5902 on a mustang 2006. I need to use the control button to program the viper to recognize that my doors, trunk, and hood are normally closed circuits. It says to open a door, turn ignition on then off, then press and hold control button until I hear a chirp. The problem is, I get no chirps. I've tried numerous combos of opening and closing the doors, but for some reason, I can't get into the program mode. I was able to do it once however, but I don't know if I screwed anything up when I tried to program it then. I could probably move on if I can reset the whole unit altogether. I am having a master installer come friday to help, maybe he can bring a bitwriter, IDK. Thanks.
Replies:
Posted By: t&t tech
Date Posted: July 28, 2010 at 8:19 PM
Do yo have the door wire connected? The unit must see ground on the green wire or 12 volts on the purple to program the unit!
-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: nuclearmuscle52
Date Posted: July 28, 2010 at 8:56 PM
Well, I was able to get into the program mode for sure, more than once. I fear that one time during programming it, I screwed it up.
Posted By: nuclearmuscle52
Date Posted: July 28, 2010 at 8:57 PM
And the door wire is connected. It's just circuited for normally closed.
Posted By: likearock
Date Posted: July 28, 2010 at 10:14 PM
I had this same problem with my 5701, it just would not go into programming mode. The bitwriter will work provided it has the correct chips in it. See my thread "viper 5701 can't program" further down the page.
Posted By: t&t tech
Date Posted: July 29, 2010 at 6:54 AM
Well if you were able to " screw up the programming" without a bitwriter then the valet button is supposed to work! Although a bitwriter would make things easier!
-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: nuclearmuscle52
Date Posted: July 29, 2010 at 9:48 AM
The valet mode is the only thing I can get it to do.
Posted By: nuclearmuscle52
Date Posted: July 29, 2010 at 10:04 AM
just bought a bitwriter 2.7 998U(exactly specified in my manual) for 20 bucks! Thanks for the replies, this will work!
Posted By: nuclearmuscle52
Date Posted: July 30, 2010 at 1:48 PM
I have the viper 5902, on a 2006 mustang
which wires do I tap into for the:
warn away(outer zone)
Full alarm(inner zone)
Posted By: nuclearmuscle52
Date Posted: July 30, 2010 at 5:49 PM
How do I get the system to unlock and lock my doors?
Posted By: t&t tech
Date Posted: August 01, 2010 at 3:47 PM
| Power Lock |
WHITE/ purple or ORANGE / black |
- |
SJB, blk 26 pin plug, pin 3 or 8 |
Notes: The SJB (Smart Junction Box) is in the passenger kick panel.
These wire are also found in each kick, in the door harness. The first wire listed is the driver switch wire and the second is the passenger switch wire. |
| Power Unlock |
dk. blue/lt. grn or yellow/red |
- |
SJB, blk 26 pin plug, pin 1 or 5 | ------------- COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: nuclearmuscle52
Date Posted: August 01, 2010 at 10:20 PM
Which wire do I wire them to?
Posted By: t&t tech
Date Posted: August 02, 2010 at 1:42 PM
The blue and green wires on the three pin harness supplied with the unit! Test and verify!
-------------
COMMIT YOUR WAY TO JEHOVAH AND HE WILL ACT IN YOUR BEHALF.
PSALMS 37:5
Posted By: nuclearmuscle52
Date Posted: August 03, 2010 at 9:45 AM
So all four wires to one, and the other four to the other?
|