04 ford explorer remote start wire

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=123721
Printed Date: May 09, 2024 at 4:42 PM

Topic: 04 ford explorer remote start wire

Posted By: soberano22
Subject: 04 ford explorer remote start wire
Date Posted: September 30, 2010 at 12:36 AM

I'm trying to install a C3-RS-915LCD remote start on my 04 explorer with factory alarm

i can match some wires from the remote start to the explorer but some idk were they go or if they don't go at all, please let me know if i can forget about some wire and were the other ones go

Ground output while running- is the ground for a bypass
second starter output- N/A
2-step unlock/factory disarm/sensor by-pass - ?

Instant start and turn off input - FOR TESTING THE REMOTE START

dome light control output - NEED RELAY FOR THIS

Horn output(programmable) - SO IF I WANT TO USE THE FACTORY HORN

Channel 4 programmable output -NEED HELP IDK

Neutral safety switch input -IDK

Ground output when disarmed -IDK

Tachometer signal input -TO TACH WIRE

Channel 6 programmable output -IDK

Accessory 2 control output -IDK

Diesel wait to start input -N/A

Ignition 3 control output -N/A

Zone 3(-) negative dor pin trigger -IDK
WHATS MY DOOR TYPE

Channel 2(trunk) output -IDK

Zone 2 negative hood/trunk trigger -TO HOOD PIN

(+)brake switch shutdown input -TO BRAKE SWITCH

Zone 3(+) positive dor pin trigger -IDK DOOR TYPE

(-) negative hood pin safety shutdown -TO DOOR PIN

Ground output when armed -TO RELAY
Channel 5 programmable output -IDK

were to mount the senser???
can use the factory led on this?

Replies:

Posted By: pitoaudiovisual
Date Posted: October 02, 2010 at 9:48 AM

ok here we go

Channel 4 and 6 are for extras like sliding doors or automatic trunk open etc not need for ur install

neutral safety switch has to see a ground for the remote starter to work usually connected to a toogle switch

Ground output when disarmed wont be used

Accessory 2 is if ur car has 2 acc wires that have to be connected for the remote starter to work

Zone 3 negative door pin is for ur doors which i believe are negative so u will connect this wire

Channel 2 is if u have an automatic open truck that u push the botton and it opens

Zone 3 is if ur doors use a positive

negative hood pin goes to the hood so if ur hood is open the car will not remote start

The sensor i usually mount under the dash on a solid part of the car

The factory led will work if u connect the factory arm and disarm wires to the alarm

-------------
Confidence is the key to any project!!

Posted By: soberano22
Date Posted: October 02, 2010 at 11:41 PM

this is great it helps alot, got some more question hope you can help

on the stage shock sensor it has

zone 1 warn away input???
zone4 ground trigger???
ground- to ground
12+volts- can i put all my +12volts on the same wire?

programmable output 2 steps unlock output???
thanks for the help

Posted By: soberano22
Date Posted: October 03, 2010 at 10:17 AM

soberano22 wrote:

this is great it helps alot, got some more question hope you can help

on the stage shock sensor it has

zone 1 warn away input???
zone4 ground trigger???
ground- to ground
12+volts- can i put all my +12volts on the same wire?

programmable output 2 steps unlock output???
thanks for the help

ok i know what to do with the shock sensor
but not the programmable output 2 steps unlock output
12+volts- can i put all my +12volts on the same wire?

Posted By: pitoaudiovisual
Date Posted: October 04, 2010 at 1:26 PM

i just responded to ur private message

-------------
Confidence is the key to any project!!