2008 honda accord, viper 5301, canmax

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=123934
Printed Date: May 09, 2024 at 8:41 PM

Topic: 2008 honda accord, viper 5301, canmax

Posted By: judgetredd77
Subject: 2008 honda accord, viper 5301, canmax
Date Posted: October 14, 2010 at 3:29 PM

Hey guys, I'm going to be installing my gear pretty soon... does anyone have experience doing this?

I browed through hundreds of posts, but never found a true guide to wiring a Viper 5301 remote starter with a CANMAX 400. I pieced the install information together and came up with this.

Does this wiring look good to you?

CANMAX 400DEI --> ACCORD
20-pin connector --> 7-pin connector (Behind key cylinder)
PIN 3 (tan) - CAN Low --> PIN 3 (blue) - Imm. Conn. (white)
PIN 4 (tan/black) - CAN High --> PIN 4 (pink) - Imm. Conn. (white)
PIN 14 (violet/white) - IMM. Data --> PIN 6 (lt. green) - Imm. Conn. (white)

CANMAX 400DEI --> VIPER 5301
4-pin D2D harness --> VIPER 5301 D2D connector

VIPER 5301 --> ACCORD
Primary (H1) 12-pin connector
H1/2 (red) - 12V input --> H3/5 (red) - H3 connector
H1/5 (black) - Ground --> Ground

Heavy gauge (H3) 8-pin connector
H3/1 (pink) - Ignition 1 (out) --> Ignition 1 (blue) - Ignition harness
H3/3 (orange) - Access. output --> Access. 1 (orange) - Ignition harness
H3/4 (violet) - Starter output --> Starter 1 (yellow) - Ignition harness
H3/5 (red) - Ignition 1 (in) --> 12V 1 (white) - Ignition harness
H3/8 (RED / black) - Acc. start. in --> H3/5 (red) - H3 connector

Remote start input 5-pin connector
PIN 1 (BLACK/ white) - Neutral sfty --> Ground
PIN 3 (brown) - Brake shutdown --> Brake (lt. green) - Brake pedal switch
PIN 5 (blue/white) - Rear defog --> Rear defrost (black)Fuse box green

Any help appreciated!
Judge

Replies:

Posted By: tedmond
Date Posted: October 15, 2010 at 10:47 PM

check your pm. but also nothing that a little searching wont find for you.

https://www.the12volt.com/installbay/downloads.asp?srch=all&term=honda+accord

download the two documents. one is a wiring guide, the other is a full DIY guide that i wrote.

good luck.

-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert

Posted By: judgetredd77
Date Posted: November 04, 2010 at 2:30 PM

OK, everything is installed (or so I think).

I can lock / unlock the doors, but I cannot get into programming mode through the valet swtich. What should I be checking? Here is what I do:

1. Turn ignition On, then Off
2. Press and hold the valet switch... nothing happens

I'll check the door pin, the pink ignition wire on my Multimeter, the Neutral Safety. Anything else I should look at?

Any help appreciated!
Judge