2008 mazda 3 remote start problems
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=124990
Printed Date: April 28, 2024 at 11:54 PM
Topic: 2008 mazda 3 remote start problems
Posted By: carlos amj
Subject: 2008 mazda 3 remote start problems
Date Posted: December 11, 2010 at 9:17 PM
Hey guys.... so i finish installing a viper 5301 in the mazda 3 2008. I know i had to add an immobilizer so I added the flcan and programmed it for the mazda. For some reason the system wont remote start. I goes through the sequence but wont crank to start. I put in the key, turn it to Ignition and remote start it and it works....
The Immobilizer wont program when its hooked up because its not weeing everything that is correct.
What do you guys think might be the problem??
Replies:
Posted By: tianot
Date Posted: December 12, 2010 at 1:13 AM
what kind of bypass you use?
automatic transmission or a manual? ------------- tianot
Posted By: carlos amj
Date Posted: December 12, 2010 at 12:59 PM
It is the FLCAN 64 from flash-it. it is flashed to < size=6 face=FuturaStd-Heavy>< size=6 face=FuturaStd-Heavy>FLC-AL(TB)-FM firmeware for mazda. And its an Automatic transmission.
Posted By: carlos amj
Date Posted: December 12, 2010 at 1:10 PM
So i was reading into some things. If i had accessory and ignition hooked up backwards would that effect the system to not remote start without the key and remote start with the key in the ignition and in the on position??...
Posted By: kohara73
Date Posted: December 12, 2010 at 3:00 PM
Did you hook up both ignition wires? One is GREEN/ YELLOW, one is pink / YELLOW.
-------------
Keith
Posted By: carlos amj
Date Posted: December 12, 2010 at 4:41 PM
I hooked the wiring according to DEI wiring. Like this...
12volts...................... BLACK/ red (30A)
Second 12volts......... Red
Starter...................... gray/black
Ignition.................... GREEN/ YELLOW
Accessory................ pink / YELLOW
Second accessory... yellow
From the viper 5301 alarm wiring I hooked it up this way......
RED / white----- 12volts
Red-------------- second 12volts
RED / black------second 12volts
Violet------------ starter
Pink-------------- ignition
Orange---------- accessory
pink/white------ second accessory this one is programmed to second accessory with bitwriter
What do you think?
Posted By: kohara73
Date Posted: December 12, 2010 at 6:16 PM
Did you actually test these wires. An ignition wire will stay on during crank, an accessory wire will drop out during crank.
-------------
Keith
Posted By: xscash
Date Posted: December 12, 2010 at 6:35 PM
did you program the flcan with 2 original keys from the car? did you follow the learn procedure without ant problems?
-------------
expandable sound
south of boston
Posted By: carlos amj
Date Posted: December 12, 2010 at 6:51 PM
Yeah I tested the wires. It seems that second accessory is actually a 2nd ignition so I reprogrammed it back to ignition2, but kept doing the same thing.
As for the immobilizer I went through the programming sequence with the two keys the customer provided. I can get it to recognize D2D but after that it won't program to the keys when I put them in the ignition.
Posted By: kohara73
Date Posted: December 13, 2010 at 5:41 AM
Have you tried remote starting it now with the key in the ignition but in the OFF position? If it starts, then you know that you just have the bypass to deal with. If it doesn't start, you'll know you have other issues.
-------------
Keith
Posted By: carlos amj
Date Posted: December 14, 2010 at 3:02 AM
Figured it out..... in the programming sequence there is a step. Missing the programming in the book. It was the bypass module. Thanks for everyones help.
|