| Print Page | Close Window |
2010 toyota camry, adslaca, viper vss5000Printed From: the12volt.comForum Name: Car Security and Convenience Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc. URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=125599 Printed Date: May 09, 2025 at 6:35 PM Topic: 2010 toyota camry, adslaca, viper vss5000 Posted By: coopapi Subject: 2010 toyota camry, adslaca, viper vss5000 Date Posted: January 10, 2011 at 9:35 PM My Camry does not have Smart Key, and I use a 40 bit key. I just installed this system, but I am missing some things. I have read all of the great stuff on here and I think I will try to give a new topic a shot.
This will be informative for most, and I will keep posting as I get this alarm 100% working. Hopefully, folks with this combo will be able to use this for their installs. Working: Horn, parking lights, Viper alarm items Partially Working: Car tries to start but immediately dies (ADSLACA not doing it's job) Not Working: Locks, Trunk, Fully functional start, and pretty much everything else :-\ The problem seems to lie in the ADSLACA. I have programmed it, every thing seems great, but after the entire procedure, the light goes out and will not come back on. I have not played with it much, but I wanted to post my progress and see who else can pitch in! So Far: H1 RED / White Aux trunk release TO ADSALCA RED / white trunk release input Red 12v constant input TO 12v Con Black IGN Harness Brown Siren TO Siren Empty Black Chassis Ground TO Chassis Ground Violet Door input TO n/u Blue Trunk instant trigger input TO ADSALCA yellow/red trunk status output Green Door input TO ADSALCA yellow/black door status output BLACK/ White Domelight output TO n/u WHITE/ Blue Remote Start activation input TO n/u White Parking light output 30 TO CamSE black parking lights (fuse box) Orange Ground when armed output TO n/u H3 BLACK/ White Neutral safety input TO Chassis ground Violet/White tach input TO ADSALCA PURPLE / white Tach (AC) output Brown Brake shut down input TO ADSALCA orange Brake output Gray Hood pin switch NO/NC input TO ADSALCA yellow hood status output Blue/White 2nd remote start status / Defogger (prgm) output TO RELAYS connected to rear defog green in kick <<NOT CONNECTED YET>> ????? Door Unlock/Lock Blue Unlock (-) Lock (+) TO ADSALCA blue/black unlock input Green Unlock (+) Lock (-) TO ADSALCA GREEN/ black lock input H2 L GREEN/ black OEM disarm output TO n/u L GREEN / WHITE OEM arm output TO n/u WHITE/ violet Aux 1 output TO n/u Violet/black Aux 2 output TO n/u WHITE/ black Aux 3 output TO n/u Light blue 2nd unlock output TO ADSALCA blue/black unlock input Gray/Black wait to start input TO n/u H4 Brown horn honk output TO CamSE white Fuse box ORANGE / Black (-) 200mA Channel 6 Output TO n/u Door Lock Green (-) lock (+) unlock TO ADSALCA GREEN/ Black lock input Blue (+) unlock (-) lock TO ADLALCA Blue/Black unlock input Relay Satellite Pink IGN 1 output TO CamSE IGN 1 / ADSALCA Yellow / Pink IGN Harness / IGN sense input RED / White 12v constant fused 30a input TO CamSE 12v Con Black IGN Harness Orange Accessory output TO CamSE Acc 1 White IGN Harness Violet Starter output (car side) TO CamSE Start 1 Blue IGN Harness Green Starter output (key side) TO CamSE Start 1 Blue IGN Harness <<I SPLICED INTO BOTH VIOLET AND GREEN BUT DID NOT CUT EITHER>> Red 12v constant fused 30a input (for IGN1 relay) TO CamSE 12v Con Black IGN Harness Pink/White (default IGN2, prgm) TO CamSE IGN 2 Pink IGN Harness Relay Satellite out Blue RS status output TO ADSALCA blue/white ground while running & CamSE Keysense Blue IGN Harness ????? Orange RS Accessory output TO n/u Violet RS starter output TO (STDP relay) GamSE IGN Harness Gray Starter 2 <<NOT CONNECTED YET!>> ????? Pink RS IGN1 output TO n/u ADS LA CA blue/white ground while running TO Viper RS out Blue RS status output & CamSE Keysense Blue IGN Harness ????? black Chassis ground TO Chassis ground red 12v constant 30amp fused TO CamSE 12v con Black IGN Harness GREEN/ black lock input TO Viper Door lock/unlock Green Unlock (+) Lock (-) blue/black unlock input TO Viper Door lock/unlock Blue Unlock (-) Lock (+) RED / white trunk release input TO Viper H1 RED / White Aux trunk release green e-brake output TO n/u PURPLE / white Tach (AC) output TO Viper RS in Violet/White tach input yellow/black door status output TO Viper H1 Green Door input yellow/red trunk status output TO Viper H1 Blue Trunk instant trigger input yellow hood status output TO Viper RS in Gray Hood pin switch NO/NC input BROWN / red CANh TO CamSE 6/black OBDII BROWN / yellow CANl TO CamSE 14/white OBDII ORANGE / black Chassis ground (OEM hood pin installed) TO Chassis ground orange Brake output TO Viper RS in Brown Brake shut down input Pink IGN input (+) TO CamSE IGN 1 Yellow IGN 1 Harness GREEN/ red code TO CamSE 4/brown Key IGN Imm gray/red txct TO CamSE 5/red Key IGN Imm Replies: Posted By: monty_77 Date Posted: January 10, 2011 at 10:12 PM are you using D2d or wire to wire
if d2d did you flash the module with dbi protocol or is it ads(will not work with the viper) you will know the firmware is right if it begins with the DBI- instead of the ADS- if wire to wire was used then it does not matter to make sure that it is the bypass and nothing else have you tried to disconnect the ground while running wire(status Wire) from the bypass and just put the key in the cylinder to see if it will start ------------- Posted By: monty_77 Date Posted: January 10, 2011 at 10:20 PM also try not to copy and past from a rich text editor like word or open office or write.
if that is a must try to copy it to notepad first then copy it again and paste here ------------- Posted By: coopapi Date Posted: January 10, 2011 at 10:26 PM monty_77 wrote: No D2D as you can see in my connections above. I hard wired everything that I could. I had it flashed with the Camry image, but like you said, it shouldn't matter. I did try it with the key in the ignition, and it still tried to start and shut right back off. I am thinking it has something to do with the RS output blue wire not being hooked to the Starter 2 wire in the Camry. My main concern is that the light is not flashing green on the bypass module. The door locks aren't working, and I guess I just thought that the ADSALCA would take care of all of the work for me (though I'm still not sure how it could unlock the doors without any connections directly to the door wires). I suppose it could... and I just don't understand it. Posted By: monty_77 Date Posted: January 10, 2011 at 11:11 PM i will look into it further
and the door locks are controlled by the bypass on the canbus network of the vehicle(More or less it just tell the computer to unlock the doors and computer does it) here this will be much easier to read H1 RED / White Aux trunk release TO ADSALCA RED / white trunk release input Red 12v constant input TO 12v Con Black IGN Harness Brown Siren TO Siren Empty Black Chassis Ground TO Chassis Ground Violet Door input TO n/u Blue Trunk instant trigger input TO ADSALCA yellow/red trunk status output Green Door input TO ADSALCA yellow/black door status output BLACK/ White Domelight output TO n/u WHITE/ Blue Remote Start activation input TO n/u White Parking light output 30 TO CamSE black parking lights (fuse box) Orange Ground when armed output TO n/u H3 BLACK/ White Neutral safety input TO Chassis ground Violet/White tach input TO ADSALCA PURPLE / white Tach (AC) output Brown Brake shut down input TO ADSALCA orange Brake output Gray Hood pin switch NO/NC input TO ADSALCA yellow hood status output Blue/White 2nd remote start status / Defogger (prgm) output TO RELAYS connected to rear defog green in kick <<NOT CONNECTED YET>> ????? Door Unlock/Lock Blue Unlock (-) Lock (+) TO ADSALCA blue/black unlock input Green Unlock (+) Lock (-) TO ADSALCA GREEN/ black lock input H2 L GREEN/ black OEM disarm output TO n/u L GREEN / WHITE OEM arm output TO n/u WHITE/ violet Aux 1 output TO n/u Violet/black Aux 2 output TO n/u WHITE/ black Aux 3 output TO n/u Light blue 2nd unlock output TO ADSALCA blue/black unlock input Gray/Black wait to start input TO n/u H4 Brown horn honk output TO CamSE white Fuse box ORANGE / Black (-) 200mA Channel 6 Output TO n/u Door Lock Green (-) lock (+) unlock TO ADSALCA GREEN/ Black lock input Blue (+) unlock (-) lock TO ADLALCA Blue/Black unlock input Relay Satellite Pink IGN 1 output TO CamSE IGN 1 / ADSALCA Yellow / Pink IGN Harness / IGN sense input RED / White 12v constant fused 30a input TO CamSE 12v Con Black IGN Harness Orange Accessory output TO CamSE Acc 1 White IGN Harness Violet Starter output (car side) TO CamSE Start 1 Blue IGN Harness Green Starter output (key side) TO CamSE Start 1 Blue IGN Harness <<I SPLICED INTO BOTH VIOLET AND GREEN BUT DID NOT CUT EITHER>> Red 12v constant fused 30a input (for IGN1 relay) TO CamSE 12v Con Black IGN Harness Pink/White (default IGN2, prgm) TO CamSE IGN 2 Pink IGN Harness Relay Satellite out Blue RS status output TO ADSALCA blue/white ground while running & CamSE Keysense Blue IGN Harness ????? Orange RS Accessory output TO n/u Violet RS starter output TO (STDP relay) GamSE IGN Harness Gray Starter 2 <<NOT CONNECTED YET!>> ????? Pink RS IGN1 output TO n/u ADS LA CA blue/white ground while running TO Viper RS out Blue RS status output & CamSE Keysense Blue IGN Harness ????? black Chassis ground TO Chassis ground red 12v constant 30amp fused TO CamSE 12v con Black IGN Harness GREEN/ black lock input TO Viper Door lock/unlock Green Unlock (+) Lock (-) blue/black unlock input TO Viper Door lock/unlock Blue Unlock (-) Lock (+) RED / white trunk release input TO Viper H1 RED / White Aux trunk release green e-brake output TO n/u PURPLE / white Tach (AC) output TO Viper RS in Violet/White tach input yellow/black door status output TO Viper H1 Green Door input yellow/red trunk status output TO Viper H1 Blue Trunk instant trigger input yellow hood status output TO Viper RS in Gray Hood pin switch NO/NC input BROWN / red CANh TO CamSE 6/black OBDII BROWN / yellow CANl TO CamSE 14/white OBDII ORANGE / black Chassis ground (OEM hood pin installed) TO Chassis ground orange Brake output TO Viper RS in Brown Brake shut down input Pink IGN input (+) TO CamSE IGN 1 Yellow IGN 1 Harness GREEN/ red code TO CamSE 4/brown Key IGN Imm gray/red txct TO CamSE 5/red Key IGN Imm ------------- Posted By: monty_77 Date Posted: January 10, 2011 at 11:25 PM you will have to connect the second starter wire on this car
on the blue starter wire you do not have to hook up the green one if you are not cutting the factory blue starter wire make sure you diode isolate the keysense and bypass from each other. that could be causing problems for the programing when you stick the key in the ignition it trigger the bypass to turn on also on the bypass you did select the wire to wire programing just to make sure ------------- Posted By: monty_77 Date Posted: January 10, 2011 at 11:35 PM if you do not have it diode isolated, after isolating it, i would reset the bypass and redo the programing.
make sure you have the starter 2 wire hooked up too ------------- Posted By: delco_installer Date Posted: January 11, 2011 at 11:55 AM Not sure if the '10 is the same as the 9 but i know for the 09 i did i needed to program the idatalink module with both keys that came with the car, put the first key in turn to on remove key and put second key in (leave in off position) should get a green light if everything is installed properly. As long as you are wired from the remote start to the bypass module using the wire to wire method and not D2D you will be ok
------------- Mike Posted By: coopapi Date Posted: January 11, 2011 at 11:22 PM delco_installer wrote: Why did you have to program both keys? Strange. I got it all working and I only programmed with one key. I'll have to try the other key to see if everything is ok. Posted By: coopapi Date Posted: January 11, 2011 at 11:29 PM Monty, thanks for the help!
I got it working, and all I had to do was connect the 2nd Starter violet wire to a relay that powers the 2nd Starter of the car (Gray). After I hooked up that wire, the Bypass Module took the program (FINALLY). I couldn't get it to take a program, but this time I got the green solid light. I immediately tried it, and it worked like a charm. The final connections pasted below make absolutely everything work perfect. Door locks, trunk, remote start, parking lights, horn, brake, tach, everything. I hope this helps someone in the future. H1 RED / White Aux trunk release TO ADSALCA RED / white trunk release input Red 12v constant input TO 12v Con Black IGN Harness Brown Siren TO Siren Empty Black Chassis Ground TO Chassis Ground Violet Door input TO n/u Blue Trunk instant trigger input TO ADSALCA yellow/red trunk status output Green Door input TO ADSALCA yellow/black door status output BLACK/ White Domelight output TO n/u WHITE/ Blue Remote Start activation input TO n/u White Parking light output 30 TO CamSE black parking lights (fuse box) Orange Ground when armed output TO n/u H3 BLACK/ White Neutral safety input TO Chassis ground Violet/White tach input TO ADSALCA PURPLE / white Tach (AC) output Brown Brake shut down input TO ADSALCA orange Brake output Gray Hood pin switch NO/NC input TO ADSALCA yellow hood status output Blue/White 2nd remote start status / Defogger (prgm) output TO RELAYS connected to rear defog green in kick Door Unlock/Lock Blue Unlock (-) Lock (+) TO ADSALCA blue/black unlock input Green Unlock (+) Lock (-) TO ADSALCA GREEN/ black lock input H2 L GREEN/ black OEM disarm output TO n/u L GREEN / WHITE OEM arm output TO n/u WHITE/ violet Aux 1 output TO n/u Violet/black Aux 2 output TO n/u WHITE/ black Aux 3 output TO n/u Light blue 2nd unlock output TO ADSALCA blue/black unlock input Gray/Black wait to start input TO n/u H4 Brown horn honk output TO CamSE white Fuse box ORANGE / Black (-) 200mA Channel 6 Output TO n/u Door Lock Green (-) lock (+) unlock TO ADSALCA GREEN/ Black lock input Blue (+) unlock (-) lock TO ADLALCA Blue/Black unlock input Relay Satellite Pink IGN 1 output TO CamSE IGN 1 / ADSALCA Yellow / Pink IGN Harness / IGN sense input RED / White 12v constant fused 30a input TO CamSE 12v Con Black IGN Harness Orange Accessory output TO CamSE Acc 1 White IGN Harness Violet Starter output (car side) TO CamSE Start 1 Blue IGN Harness Green Starter output (key side) TO CamSE Start 1 Blue IGN Harness <<I SPLICED INTO BOTH VIOLET AND GREEN BUT DID NOT CUT EITHER>> Red 12v constant fused 30a input (for IGN1 relay) TO CamSE 12v Con Black IGN Harness Pink/White (default IGN2, prgm) TO CamSE IGN 2 Pink IGN Harness Relay Satellite out Blue RS status output TO ADSALCA blue/white ground while running Orange RS Accessory output TO n/u Violet RS starter output TO (STDP relay) GamSE IGN Harness Gray Starter 2 Pink RS IGN1 output TO n/u ADS LA CA blue/white ground while running TO Viper RS out Blue RS status output black Chassis ground TO Chassis ground red 12v constant 30amp fused TO CamSE 12v con Black IGN Harness GREEN/ black lock input TO Viper Door lock/unlock Green Unlock (+) Lock (-) blue/black unlock input TO Viper Door lock/unlock Blue Unlock (-) Lock (+) RED / white trunk release input TO Viper H1 RED / White Aux trunk release green e-brake output TO n/u PURPLE / white Tach (AC) output TO Viper RS in Violet/White tach input yellow/black door status output TO Viper H1 Green Door input yellow/red trunk status output TO Viper H1 Blue Trunk instant trigger input yellow hood status output TO Viper RS in Gray Hood pin switch NO/NC input BROWN / red CANh TO CamSE 6/black OBDII BROWN / yellow CANl TO CamSE 14/white OBDII ORANGE / black Chassis ground (OEM hood pin installed) TO Chassis ground orange Brake output TO Viper RS in Brown Brake shut down input Pink IGN input (+) TO CamSE IGN 1 Yellow IGN 1 Harness GREEN/ red code TO CamSE 4/brown Key IGN Imm gray/red txct TO CamSE 5/red Key IGN Imm Posted By: coopapi Date Posted: January 12, 2011 at 8:55 PM This should make more sense... I made a couple of changes!
H1 RED / White Aux trunk release TO ADSALCA RED / white trunk release input Red 12v constant input TO 12v Con Black IGN Harness Brown Siren TO Siren Empty Black Chassis Ground TO Chassis Ground Violet Door input TO n/u Blue Trunk instant trigger input TO ADSALCA yellow/red trunk status output Green Door input TO ADSALCA yellow/black door status output BLACK/ White Domelight output TO n/u WHITE/ Blue Remote Start activation input TO n/u White Parking light output 30 TO CamSE black parking lights (fuse box) Orange Ground when armed output TO n/u H3 BLACK/ White Neutral safety input TO Chassis ground Violet/White tach input TO ADSALCA PURPLE / white Tach (AC) output Brown Brake shut down input TO ADSALCA orange Brake output Gray Hood pin switch NO/NC input TO ADSALCA yellow hood status output Blue/White 2nd remote start status / Defogger (prgm) output TO RELAYS to make a latched positive and connected to the large (+) white cable that runs down the driver's side molding. Door Unlock/Lock Blue Unlock (-) Lock (+) TO ADSALCA blue/black unlock input Green Unlock (+) Lock (-) TO ADSALCA GREEN/ black lock input H2 L GREEN/ black OEM disarm output TO n/u L GREEN / WHITE OEM arm output TO n/u WHITE/ violet Aux 1 output TO n/u Violet/black Aux 2 output TO n/u WHITE/ black Aux 3 output TO n/u Light blue 2nd unlock output TO ADSALCA blue/black unlock input Gray/Black wait to start input TO n/u H4 Brown horn honk output TO CamSE white Fuse box ORANGE / Black (-) 200mA Channel 6 Output TO n/u Door Lock Green (-) lock (+) unlock TO ADSALCA GREEN/ Black lock input Blue (+) unlock (-) lock TO ADLALCA Blue/Black unlock input Relay Satellite Pink IGN 1 output TO CamSE IGN 1 / ADSALCA Yellow / Pink IGN Harness / IGN sense input RED / White 12v constant fused 30a input TO CamSE 12v Con Black IGN Harness Orange Accessory output TO CamSE Acc 1 White IGN Harness Violet Starter output (car side) TO CamSE IGN Harness Start 1 Blue IGN Harness & CamSE IGN Harness Gray Start 2 Green Starter output (key side) TO n/u Red 12v constant fused 30a input (for IGN1 relay) TO CamSE 12v Con Black IGN Harness Pink/White (default IGN2, prgm) TO CamSE IGN 2 Pink IGN Harness Relay Satellite out Blue RS status output TO ADSALCA blue/white ground while running Orange RS Accessory output TO n/u Violet RS starter output TO (STDP relay) GamSE IGN Harness Gray Starter 2 Pink RS IGN1 output TO n/u ADS LA CA blue/white ground while running TO Viper RS out Blue RS status output black Chassis ground TO Chassis ground red 12v constant 30amp fused TO CamSE 12v con Black IGN Harness GREEN/ black lock input TO Viper Door lock/unlock Green Unlock (+) Lock (-) blue/black unlock input TO Viper Door lock/unlock Blue Unlock (-) Lock (+) RED / white trunk release input TO Viper H1 RED / White Aux trunk release green e-brake output TO n/u PURPLE / white Tach (AC) output TO Viper RS in Violet/White tach input yellow/black door status output TO Viper H1 Green Door input yellow/red trunk status output TO Viper H1 Blue Trunk instant trigger input yellow hood status output TO Viper RS in Gray Hood pin switch NO/NC input BROWN / red CANh TO CamSE 6/black OBDII BROWN / yellow CANl TO CamSE 14/white OBDII ORANGE / black Chassis ground (OEM hood pin installed) TO Chassis ground orange Brake output TO Viper RS in Brown Brake shut down input Pink IGN input (+) TO CamSE IGN 1 Yellow IGN 1 Harness GREEN/ red code TO CamSE 4/brown Key IGN Imm gray/red txct TO CamSE 5/red Key IGN Imm |
| Print Page | Close Window |