556h yeah an old model
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=125650
Printed Date: July 02, 2025 at 5:50 AM
Topic: 556h yeah an old model
Posted By: Thack79
Subject: 556h yeah an old model
Date Posted: January 13, 2011 at 12:16 PM
trying to get rid of this for a while but i have a 556H and have a issue with this green reference wire and where the heck it goes. https://www.directedstore.com/manuals/556HW.pdf
its a five pin plug the the wire its directing to, its NO pin there. Ive searched already and some tried to use the BROWN / black (negative) the ONLY other wire inthat harness that is not used and it didnt work. Can any one offer any expertise so i can get rid of this module?
Thanks!!
Replies:
Posted By: Thack79
Date Posted: January 13, 2011 at 12:17 PM
and its for a 2002 honda accord ex
Posted By: tedmond
Date Posted: January 13, 2011 at 12:49 PM
connect referance wire to pin 1.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: kreg357
Date Posted: January 13, 2011 at 12:58 PM
Good question. Here is a link to the Fortin Key-Override-All for the 2002 Accord. https://ifar.ca/download/425/preview.html It is a 5 Pin connector and the colors match up but there is no pin outboard of the Ignition wire... Pin 1 in cars with a 7 Pin connector using Mode 1 is chassis ground. Might give it a try that way. ------------- Soldering is fun!
Posted By: Thack79
Date Posted: January 13, 2011 at 1:09 PM
as always thanks guys!!!
Posted By: Thack79
Date Posted: January 13, 2011 at 1:29 PM
tedmond pin 1 is the ignition wire (yellow/black) Pin 4 wire is the BROWN / black (negative). is that the one you are refering to? There is no wire in pin 5.
Posted By: Thack79
Date Posted: January 13, 2011 at 1:32 PM
Posted By: kreg357
Date Posted: January 13, 2011 at 1:44 PM
Did you try it going to chassis ground? (Just connected to the remote starts chassis ground wire connection.)
-------------
Soldering is fun!
Posted By: Thack79
Date Posted: January 13, 2011 at 1:56 PM
I dont have a way to DMM stuff like this since the instructions are a lil crazy . I havent tried it yet , but wanted to get second opinions who may have seen this before i just "guessed"
Posted By: ayalja123
Date Posted: September 06, 2011 at 4:29 PM
I'm having the same problem. Does anyone know where this green wire goes?
Posted By: ayalja123
Date Posted: September 26, 2011 at 7:32 PM
I'm still trying to figure out where this reference wire is. anyone? please,thanks
Posted By: enice
Date Posted: September 26, 2011 at 10:50 PM
I would connect it to the BROWN / black wire on plug. The issue may be the way you are programming it. As mentioned before the reference wire is a negative input. Programming may be a little confusing. I had a few that i got rid of and i had to basically follow the programming steps but i do it and turn off the car and then restart the car with the key. That is something the instructions didn't mention and it has worked.
Posted By: metz35
Date Posted: September 27, 2011 at 3:20 PM
keysense...........
Posted By: ayalja123
Date Posted: September 27, 2011 at 5:44 PM
Thanks guys i'll try that.
|
