2006 focus python 1401
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=125704
Printed Date: May 15, 2025 at 9:15 PM
Topic: 2006 focus python 1401
Posted By: dblake
Subject: 2006 focus python 1401
Date Posted: January 16, 2011 at 11:19 PM
I am very familiar with electronics in general. never have done a install for a remote start though. want to make sure i am on the correct note.... please help guys.
im going to mark ones that i think i do not need to hookup with a *NOT USED* and ones i am not sure about with *?????*
tell me if im right. Thankyou!
Main Harness (H1), 12-pin connector
H1/1 RED / WHITE (-) 200mA AUX/TRUNK RELEASE OUTPUT
H1/2 RED (+)12VDC CONSTANT INPUT
H1/3 BROWN (-) 200mA HORN HONK OUTPUT
H1/4 WHITE/ BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay
H1/5 BLACK (-) CHASSIS GROUND
H1/6 VIOLET (+) DOOR TRIGGER INPUT
H1/7 BLUE* FACTORY HORN INPUT (Use jumper to set polarity) *?????*
H1/8 GREEN (-) DOOR TRIGGER INPUT (N/C** OR N/O)
H1/9 BLACK/ WHITE (-) 200mA DOME LIGHT SUPERVISION OUTPUT *NOT USED*
H1/10 WHITE/ BLUE (-) REMOTE START/ TURBO TIMER ACTIVATION INPUT *?????*
H1/11 WHITE PARKING LIGHT OUTPUT
H1/12 ORANGE (-) 500mA GROUND WHEN LOCKED OUTPUT *NOT USED*
H2 Harness, 18-pin connector
H2/1 LIGHT GREEN/ BLACK (-) 200mA OEM ALARM DISARM OUTPUT *?????*
H2/2 ORANGE / BLACK (-) 200mA AUX 4 OUTPUT *NOT USED*
H2/3 GREEN / WHITE (-) 200mA OEM ALARM ARM OUTPUT *NOT USED*
H2/4 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT *NOT USED*
H2/5 WHITE/ BLACK (-) 200mA AUX 3 OUTPUT *NOT USED*
H2/6 WHITE/ VIOLET (-) 200mA AUX 1 OUTPUT *NOT USED*
H2/7 GREY/BLACK (-) DIESEL WAIT TO START INPUT *NOT USED*
H2/8 N/A *NOT USED*
H2/9 VIOLET/WHITE TACHOMETER INPUT
H2/10 DARK BLUE (-) 200mA STATUS OUTPUT *?????*
H2/11 PINK/WHITE (-) 200mA FLEX RELAY CONTROL OUTPUT *NOT USED*
H2/12 ORANGE (-) 200mA ACCESSORY OUTPUT *NOT USED*
H2/13 PURPLE (-) 200mA STARTER OUTPUT *NOT USED*
H2/14 PINK (-) 200mA IGNITION 1 OUTPUT *NOT USED*
H2/15 GREY (-) HOOD PIN INPUT (N/C OR N/O)
H2/16 BLUE/WHITE (-) 200mA 2ND STATUS /REAR DEFOGGER OUTPUT *NOT USED*
H2/17 BROWN (+) BRAKE SHUTDOWN INPUT
H2/18 BLACK/ WHITE (-) NEUTRAL SAFETY INPUT
Remote Start, (H3) 8-pin connector
H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT
H3/2 RED / WHITE +12V FUSED (30A) IGNITION 2/FLEX RELAY INPUT *?????*
H3/3 ORANGE (+) ACCESSORY OUTPUT *NOT USED*
H3/4 VIOLET (+) STARTER OUTPUT
H3/5 RED +12V FUSED (30A) IGNITION 1 INPUT
H3/6 PINK/WHITE IGNITION 2/FLEX RELAY OUTPUT *NOT USED*
H3/7 PINK/BLACK FLEX RELAY INPUT 87a (IF REQUIRED) OF FLEX RELAY *?????*
H3/8 RED / BLACK +12V FUSED (30A) ACCESSORY/STARTER INPUT *?????*
i just need a better idea of what NEEDS to be hooked up and what does not.
Also what else do i need? i have a relay and harness but do i need anything for factory security system?
im using this for the wires....
https://www.directwholesale.net/diagrams/printpage.asp?ModelID=14085&MakeID=18
if someone would like to copy and paste the part on each wire and tell me which ones NOT to hookup i would greatly appreciate it! :)
Replies:
Posted By: howie ll
Date Posted: January 17, 2011 at 3:34 AM
H/1 4 N/A
H/1 6 N/A
H1/ 7 Do you have a factory alarm?
H1/ 10 NA
H2/ 1 and 3, again is there a factory alarm?
H2/ 10 Will be used to trigger whatever by-pass you need.
H3/ 2, 6, and 7 N/A
H/3 8 Connect.
PM me with your email address, I'll send you the DEI list for this vehicle.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: dblake
Date Posted: January 17, 2011 at 8:10 AM
thankyou! i pm'ed you!
which bypass module do i need now?
Posted By: dblake
Date Posted: January 17, 2011 at 4:59 PM
what is a good bypass that is not super expensive..?
installing python 1401
if it is without another key id prefer that
thanks guys 
Posted By: Twelvoltz
Date Posted: January 17, 2011 at 6:09 PM
DEI 1100F can be had online really cheap and has been proven extremely reliable. You need two valid keys to program it but do not have to lose a key to use it.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: dblake
Date Posted: January 17, 2011 at 8:56 PM
any others you recommend?
Posted By: Twelvoltz
Date Posted: January 18, 2011 at 7:39 AM
The 1100F is probably the cheapest you will find. However there are a ton of options. My preference in bypass modules are those made by Idata. In actuality although the 1100F is labeled as DEI, I believe it was made by Idata and labeled as DEI.
Here is what Idata offers for your 06 Fusion: link------------- Installer, IT support, and FFL. I need less hobbies.
Posted By: howie ll
Date Posted: January 18, 2011 at 8:03 AM
Thanks Twelvoltz, I was a bit lost here, in the UK we've had 3 body changes and 3 wiring part colour changes since 98, thank goodness this year's new model will be the same on both sides of the pond.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: dblake
Date Posted: January 18, 2011 at 6:37 PM
Bought the ADS-TB at local dealer, 47 and some cents and they programmed it for me :) now i just need to get the girlfriend over to get it installed :) thanks i may have more questions
Posted By: dblake
Date Posted: January 18, 2011 at 8:50 PM
confused on the heavy geauge wires on which ones to hookup....
Remote Start, (H3) 8-pin connector
H3/1 PINK (+) IGNITION 1 INPUT/OUTPUT Confused on where this one goes and other ignition (h5)
H3/2 RED / WHITE +12V FUSED (30A) IGNITION 2/FLEX RELAY INPUT *NOT USED*
H3/3 ORANGE (+) ACCESSORY OUTPUT *NOT USED*
H3/4 VIOLET (+) STARTER OUTPUT GOOD
H3/5 RED +12V FUSED (30A) IGNITION 1 INPUT where does this go
H3/6 PINK/WHITE IGNITION 2/FLEX RELAY OUTPUT *NOT USED*
H3/7 PINK/BLACK FLEX RELAY INPUT 87a (IF REQUIRED) OF FLEX RELAY *NOT USED*
H3/8 RED / BLACK +12V FUSED (30A) ACCESSORY/STARTER INPUT where does this go?
Posted By: howie ll
Date Posted: January 19, 2011 at 12:34 AM
H3/1 Pink to GREEN/ YELLOW
H3/2 RED / white not used.
H3/3 Orange to Yellow.
H3/4 Violet to Grey/Black
H3/5 To Red at ignition or + Battery, fused at battery.
H3/6 Not used.
H3/7 Not used.
H3/8 Connected at the same point as Red H3/5, fused independently.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: dblake
Date Posted: January 22, 2011 at 1:17 PM
PINK - IGNITION INPUT- DO NOT CONNECT THE IGNITION INPUT AT THE PATS MODULE, CONNECT TO THE
MAIN VEHICULE IGNITION INSTEAD
this is for the bypass.....
which ignition do i connect this to?
Posted By: howie ll
Date Posted: January 22, 2011 at 3:41 PM
GREEN/ YELLOW on the ignition loom.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: dblake
Date Posted: January 31, 2011 at 8:11 PM
all set guys! everything worked first time :) bypass module was hard to program because my girlfriend forgot the second key so i got it all back together...then when i tried to program it i could not see LED status... but with a mirror it took care of seeing the LED. Thanks a ton for the help! all connections were soldered and wrapped for less problems.
|