keysense and 2006 hyundai sonata
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=125725
Printed Date: May 08, 2024 at 1:46 AM
Topic: keysense and 2006 hyundai sonata
Posted By: apuga0621
Subject: keysense and 2006 hyundai sonata
Date Posted: January 17, 2011 at 9:54 PM
Attempting to install a viper 5301. Hooked up the factory hood pin to the bcm, green wire pin 24, turned off the tach, and double checked all ignition, accessories(both green and orange), and starter wires with DMM. I hooked up the factory arm and disarm wire, but it will not start. The parking lights blink about 6 times and nothing happens. Is a keysense wire needed for this car? Car does not have a transponder.
Replies:
Posted By: pitoaudiovisual
Date Posted: January 17, 2011 at 10:20 PM
no the car doesnt have a key sense. check to make sure that the hood pin is not throwing a negative even when its closed also double check the brake wire sometimes u can hook up the wrong brake wire and if it shows positive the car wont start. Also did u install the neutral safety switch.
-------------
Confidence is the key to any project!!
Posted By: apuga0621
Date Posted: January 17, 2011 at 11:24 PM
Brilliant! I noticed the hood pin switch was showing 0.3 positive volts when the hood was closed and a ground (-) when it was open.
I used the green wire on the brake switch, seemed to test out ok. Will double check.
Grounded the neutral safety switch.
Also looking to hook up rear defrost. Is there a defrost wire on the BCM?
Thanks for your help.
Posted By: tedmond
Date Posted: January 18, 2011 at 12:03 AM
check diagnostics as to why it wont start. has it been set for automatic tranny if it is?
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: apuga0621
Date Posted: January 18, 2011 at 1:11 PM
Parking lights were blinking 8 times. Diagnostic said it was a neutral safety switch error. The transmission was already in automatic and checked the ground. I have the chassis ground and neutral safety tied to the same point. Car still does not start, everything else works ok (passive door locks and trunk release).
Posted By: buddholly
Date Posted: January 18, 2011 at 2:07 PM
Is it set for an automatic??
Posted By: buddholly
Date Posted: January 18, 2011 at 2:08 PM
Oops didnt read your entire post.
Posted By: tony_g
Date Posted: January 18, 2011 at 2:38 PM
have you tried starting the car manually then attempt to do the quick stop feature (valet take over) to see if the r/s keep it running that way. how about connecting tach wire,always works 100% for me
Posted By: apuga0621
Date Posted: January 18, 2011 at 2:57 PM
no problem. At this point i am stumped. Here are my wire connections. May be i connected something wrong or there is an on board jumper setting not set correctly. Any help is appreciated.
HEAVY GAUGE REMOTE START 8-PIN
------------------------------
H3/1 hooked to Blue @ ignition harness
H3/2 -> pink 12v const
H3/3 -> orange (acc 1)
H3/4 -> green (starter)
H3/5 -> red (12v const)
H3/6 -> green (acc2 programed as acc)
H3/7 -> not used
H3/8 -> red (12v const)
REMOTE START INPUT 5-PIN
-------------------------
1 -> grounded to chassis
2 -> not used (programmed tach off)
3 -> green (at brake switch, reads 12v when pressed)
4 -> grounded to chasis (programmed NC, was BCM pin 24)
5 -> not used.
on 12 pin connector all wires are used except H1/4, H1/10, and H1/12
factory alarm and disarm connected at kick panel and verified with multimeter.
Posted By: tony_g
Date Posted: January 18, 2011 at 3:14 PM
has the shutdown toggle switch been connected to the brain as well and turned to the on position?
Posted By: apuga0621
Date Posted: January 18, 2011 at 3:20 PM
thanks for your quick reply tony_g. I am in the process of hunting down the tach wire. I think it is in the driver's kick panel on a black connector (white wire) or at the instrument cluster.
is the toggle switch need for this remote start to function?
Posted By: tony_g
Date Posted: January 18, 2011 at 3:29 PM
yes it has to be connected to the brain in the appropriate socket and set to on for the r/s to start. its just a safety switch that you normally hide in the car to shutdown the r/s when you lend the car to someone or have the car in for repairs servicing ect and dont want anyone to be able to use it. i initially forgot to put mine in then saw it sitting on my passenger seat when i attempted a remote start after installing and it didnt start. its always the simplest and most straightforward things that cause problems and we overlook them, hopefully thats all thats stopping it from working .
Posted By: apuga0621
Date Posted: January 18, 2011 at 3:36 PM
Oh Mylanta! I am such an idiot. Thanks tony_g for that. Thank you all for your help. Attached the toggle switch and flipped it on, with no tach wire and car started.
Great forum and great peeps.
if any one is interested here is a link to the wiring diagram i got from wire color: https://www.megaupload.com/?d=A917R7Q7. If i am breaking any rules, sorry. You can also pm me and i'll send it.
Posted By: tony_g
Date Posted: January 18, 2011 at 3:48 PM
no problem glad its working for you now, its always something simple that we overlook that stumps us lol.
|