clifford 650 c/w intellistart new fob
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=125822
Printed Date: May 10, 2025 at 5:00 AM
Topic: clifford 650 c/w intellistart new fob
Posted By: i-vtec
Subject: clifford 650 c/w intellistart new fob
Date Posted: January 24, 2011 at 6:49 AM
Hi, I have bought a damaged Honda civic type R 2002, and the owner had lost the key. and alarm fob.
I have removed the complete Alarm system.
Its a Clifford concept 650 with Intellistart 4.
How can i get a replacement new fob (programmed), along with a new Valet code.
Appreciated If some one can help me out.
Replies:
Posted By: howie ll
Date Posted: January 24, 2011 at 8:33 AM
Armour Auto or a local dealer, you have to know if it's a Mk l or Mk ll 650.
The Mk ll will have two multi pin white connector blocks, also if you intend using it again order the new looms, plus LED and Valet switch looms. Did you remove the dual-zone prox and its lead and the antenna and its lead it won't even work without the antenna, also unless you have a Wizz software or know the valet pin code don't bother.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: i-vtec
Date Posted: January 24, 2011 at 9:02 AM
Its Mk 1, and yes i have removed all wiring loom,sensors , antenna etc etc.
I do have the Wizard software but i couldn't use the software on my lap top on my other car last time.
Would the wizard work on vista?
Would the alarm unit need to be wired on to car in order for ne fob to be programmed.
Previous owner said, he never had no code, but he does have the booklet,would their be any info in the booklet at all.
Posted By: howie ll
Date Posted: January 24, 2011 at 10:06 AM
If you have the booklet the code number is on the back.
You can set it up on the bench, 5amp and 20amp power, one of the grounds, ignition input, siren, LED and aerial all need to be connected.
Your computer needs to have a serial port and pref Win 98 SE.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: i-vtec
Date Posted: January 24, 2011 at 10:09 AM
Ok, so If its all set up like you said on a bench, and If i have the valet code, can i not programme a new fob via the programming feature?.
And thank you for your kind support.
Posted By: howie ll
Date Posted: January 24, 2011 at 10:32 AM
Yes. Done it many, many times.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: howie ll
Date Posted: January 24, 2011 at 10:34 AM
Yes, if you have the Valet pin code you don't need a computer, just go into user programming, erase the remotes and add the new.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
|