need odyssey 04 wire diagram

Hi,

I am looking for a Odyssey 04 Ex-L wire diagram for remote start and 2 slides door but can't find it. I will wire it with Viper 5701 remote start. If anyone have a wire diagram please share with me. I will appreciate it.

Thanks,

Thang

https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp

MODEL       YEAR(S)
ODYSSEY       2004 -
KEY       T-HARNESS       IMMOBILIZER
N/A       N/A       HONDA'S TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY
PART       COLOR       LOCATION
12 VOLT CONSTANT       WHITE (+)       IGNITION SWITCH HARNESS
STARTER       BLACK/ WHITE (+)       IGNITION SWITCH HARNESS
STARTER 2       N/A      
IGNITION 1       BLACK / YELLOW (+)       IGNITION SWITCH HARNESS
IGNITION 2       N/A      
IGNITION 3       N/A      
ACCESSORY /HEATER BLOWER 1       YELLOW (+)       IGNITION SWITCH HARNESS
ACCESSORY /HEATER BLOWER 2       WHITE/ BLACK (+)       IGNITION SWITCH HARNESS
KEYSENSE       N/A      
PARKING LIGHTS ( - )       N/A      
PARKING LIGHTS ( + )       RED / BLACK (+)       @ 10 PIN PLUG DRIVER SIDE FUSEBOX
POWER LOCK       BLACK/ BLUE (TYPE B) See NOTE *1       @ PASSENGER SIDE FUSEBOX, See NOTE *2
POWER UNLOCK       ORANGE (TYPE B) See NOTE *1       @ PASSENGER SIDE FUSEBOX, See NOTE *2
DOOR TRIGGER       BLACK/ WHITE (-), Requires Part #775 Relay       @ INTERIOR LIGHT SWITCH
DOMELIGHT SUPERVISION       LIGHT GREEN (-), Requires Part #775 Relay       @ INTERIOR LIGHT SWITCH
TRUNK RELEASE       N/A      
SLIDING POWER DOOR       N/A      
HORN       LIGHT GREEN/ BLUE (-)       @ STEERING COLUMN HARNESS
TACH       BLUE       @ 2-PIN PLUG ABOVE BRAKE MASTER CYLINDER
WAIT TO START LIGHT       N/A      
BRAKE       WHITE/ BLACK (+)       @ SWITCH ABOVE BRAKE PEDAL
FACTORY ALARM DISARM       See NOTE * 3      
ANTI-THEFT       TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY       TRANSPONDER @ IGNITION SWITCH TUMBLER
EXTRA INFORMATION
NOTE *1 these wires can ONLY be metered or tested buy turning the key in the PASSENGER DOOR KEY CYLINDER. NOTE *2 these wires are found in a 20-pin plug on the LX models and on the EX models the wires are in a 3-pin plug. NOTE *3 the DISARM wire on the EX is a BLACK/ RED to BLUE (-) in the DRIVERS DOOR Module in the drivers door.

Thank you monty_77

Right now I am planning the wiring connection and I don't know where to connect some of wires from remote to... I hope someone could help me point out where are these connection connect to. This is my 1st time install/mod car electrical.

H1/4 wht/bro flex parking light relay 87A
H1/7 blue trunk (-) instant trigger input
H1/8 green door (-) input
H1/10 wht/ble remote start activation (-) input
H1/12 orange ground when armed (-) 500mA output

RS in blu/wht 2nd remote start status (-) output

H2/2 light GREEN/ wht oem arm (-) 200mA output
H2/6 light blue 2nd unlock (-) 200mA output
H2/8 bro/blk (-) 200mA horn honk output connect to horn?

H3/2 RED / wht fused 30A (contact 87 of rS flex relay) connect to #775 relay?
H3/3 orange accessory output connect to yellow(+) and/or wht/blk (+)??
H3/4 violet starter output connect to blk/wht (+)?
H3/5 green starter input (does it connect to wht (+)12V constant?)
H3/6 red 12V(+) constant connect to wht(+)??
H3/9 RED / blk for accessory and starter relays?


Thanks

thang25 wrote:

---

H1/4 wht/bro flex parking light relay 87
H1/7 blue trunk (-) instant trigger input

---

You will not need ether of these wire for the remote starter

thang25 wrote:

---

H1/8 green door (-) input

---

DOOR TRIGGER       BLACK/ WHITE (-)

thang25 wrote:

---

H1/10 wht/ble remote start activation (-) input

---

will not us this, it used to start the remote start from something like door locks pressed three times.

thang25 wrote:

---

H1/12 orange ground when armed (-) 500mA output

---

hook to something you want to turn on when doors are locked (like extra sensors)

thang25 wrote:

---

RS in blu/wht 2nd remote start status (-)output

---

This will be used on the Status wire of bypass also known as GWR (Ground While Running)

thang25 wrote:

---

H2/2 light GREEN/ wht oem arm (-) 200mA output

---

Will not use this wire

thang25 wrote:

---

H2/6 light blue 2nd unlock (-) 200mA output

---

you will only use this if you want to set up drivers door priority and if you don't want to don't worry about it

thang25 wrote:

---

H2/8 bro/blk (-) 200mA horn honk output connect to horn?

---

HORN       LIGHT GREEN/ BLUE (-)       @ STEERING COLUMN HARNESS

you do not need to hook it up but it will help with programming

thang25 wrote:

---

H3/2 RED / wht fused 30A (contact 87 of rS flex relay) connect to #775 relay?

---

you will want to hook this to a 12 volt source. white wire

this will power the pink/white wire.

thang25 wrote:

---

H3/3 orange accessory output connect to yellow(+) and/or wht/blk (+)??

---

only hook it to one of the two you can use the programable pink/white for the other one

thang25 wrote:

---

H3/4 violet starter output connect to blk/wht (+)?

---

yes hook it to the blk/wht in the ignition harness

thang25 wrote:

---

H3/5 green starter input (does it connect to wht (+)12V constant?)

---

no this wire can be hooked to the starter wire for anti-grind(starter kill) feature

if you want to hook this up you will have to cut the starter BLACK/ white wire and hook this one to key side of wire and the violet starter output to the vehicle side of the wire.

thang25 wrote:

---

H3/6 red 12V(+) constant connect to wht(+)??

---

yes will get hooked to the white 12 volt

thang25 wrote:

---

H3/9 RED / blk for accessory and starter relays?

---

this will get hooked to the white 12 volt also

please note that you can hook all the 12 volts to battery too

Thank for your information...

I tried find a blue wire for tachometer above the brake paddle and I can't find it. Does it locate any other location?

Thanks.

in a lt blue connector in the drivers kick panel (blue wire)



it might be blue with silver on it not a strip

Never mind I found it. How do it find blue tachometer inside the van?

I tried to find a factory disarm alarm wire with "NOTE *3 the DISARM wire on the EX is a BLACK/ RED to BLUE (-) in the DRIVERS DOOR Module in the drivers door"

Could someone tell me what is BLACK/ red to blue (-) mean??? I found blue/red wire but no BLACK/ red or blue in a driver door box.

It just means that wire changes from BLACK/ red to blue after a connector somewhere in the vehicle. Basically that wire is located on the door lock switch inside of the door, I would also check for it comming out of the door harness, probably a thin little wire.

Can someone help please...

How do I change the setting from manual transmission to automatic ??

Thanks again.

I still have couple problem that I could not fix, and I need your help. And I want to thank you in advance.

1) Does anyone know where to find a wire diagram for 775 relay that connect to Door trigger, and Domelight supervisor?
2) Does anyone know how to find a right wire for Factory disarm wire? How do I know if I got a right wire?


Thang

Does anyone know why my Viper 5701, I could not change the setting from Manual to Auto trans?

I pushed a door trigger
turn a key to On then Off, with in 10 secs
I pressed a valet key for 30 secs to 1 min and still not LED flashing.

Can anyone help me?

Thanks in advance.

Thang