remote starter crank but not starting

Hi,
 
I need your help. I just installed viper 5301 with 1101T bypass module. The car will crank but won’t start. It is like if you start with immobilizer kicking in but i have the key working inside the car.
 
Is there any solution?
 
thx

sorry forgot to say i got infiniti m56 and it has intelligent key

If you leave the functional key fob in the car, will your car start? With the 1101 unplugged. This will tell us if the 1101 is the problem.

-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.

No it won't start .. I folloed the install manual which I got from here but for Push 2 start should I follow the manual complitlly or is their any defferance?

What year is your infiniti?

-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.

Have you connected the following:

Starter     brown (push-button start)(-) Push-button ignition switch or BCM, white 40 pin plug, pin 30

Second Starter     lt. blue (-) BCM, white 40 pin plug, pin 27

And, did you install the relay in the engine compartment for neutral
safety switch.

It would so much easier if you would have gotten the idata link
ADS-AL-CA. Anyhow, you can send me an email directly..check my profile and I can send you pdf files that explains what to do.



-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.

It is 2011

hi

today i pushed the PTS button twice to the"on" light

then i remote started the car with the key inside it does remote start

then when i tried to do the same without the key inside the car i wont start

any ideas?

Check your ignition wiring.

hi

the Starter   brown (push-button start)(-) is connected to (-) 200mA STARTER OUTPUT

i did not connect Second Starter     lt. blue (-) BCM, white 40 pin plug, pin 27 to the remote starter

any ideas?

Primary harness (H1), 12-pin connector
H1/1
RED / WHITE
(-) 200mA TRUNK RELEASE OUTPUT
H1/2
RED
(+)12v CONSTANT INPUT
H1/3
BROWN
(-) HORN OUTPUT
H1/4
WHITE/ BROWN
LIGHT FLASH ISOLATION WIRE - PIN 87a of onboard relay
H1/5
BLACK
(-) CHASSIS GROUND
H1/6
VIOLET
(+) DOOR TRIGGER INPUT*
H1/7
BLUE
(-) FACTORY HORN INPUT
H1/8
GREEN
(-) DOOR TRIGGER INPUT*
H1/9
BLACK/ WHITE
(-) 200mA DOME LIGHT OUTPUT
H1/10
WHITE/ BLUE
(-) REMOTE START/ TURBO TIMER ACTIVATION INPUT
H1/11
WHITE
PARKING LIGHT OUTPUT
H1/12
ORANGE
(-) 500mA GROUND WHEN ARMED OUTPUT

---------------------
Auxiliary harness (H2), 7-pin connector
H2/1
LIGHT GREEN/ BLACK
(-) 200mA FACTORY ALARM DISARM OUTPUT
H2/2
LIGHT GREEN / WHITE
(-) 200mA FACTORY ALARM ARM OUTPUT
H2/3
WHITE/ VIOLET
(-) 200mA AUX 1 OUTPUT
H2/4
VIOLET/BLACK
(-) 200mA AUX 2 OUTPUT
H2/5
WHITE/ BLACK
(-) 200mA AUX 3 OUTPUT
H2/6
LIGHT BLUE
(-) 200mA 2ND UNLOCK OUTPUT
H2/7
GRAY/BLACK
(-) DIESEL WAIT TO START INPUT

----------------------------

Heavy gauge remote start, (H3) 8-pin connector
H3/1
PINK
IGNITION 1 INPUT/OUTPUT
H3/2
RED / WHITE
(+) FUSED (30A) IGNITION 2 / FLEX RELAY INPUT 87
H3/3
ORANGE
ACCESSORY OUTPUT
H3/4
VIOLET
STARTER OUTPUT
H3/5
RED
(+) FUSED (30A) IGNITION 1 INPUT
H3/6
PINK/WHITE
(+) IGNITION 2 / FLEX RELAY OUTPUT 30
H3/7
PINK/BLACK
FLEX RELAY INPUT 87A key side (if required) of FLEX RELAY
H3/8
RED / BLACK
(+) FUSED (30A) ACCESSORY/STARTER INPUT

-----------------------------
Remote start input, 5-pin connector
1
BLACK/ WHITE
(-) NEUTRAL SAFETY SWITCH INPUT
2
VIOLET/WHITE
TACHOMETER INPUT
3
BROWN
(+) BRAKE SHUTDOWN INPUT
4
GRAY
N/O or N/C (-) HOOD PIN SWITCH INPUT
5
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT



Remote start auxiliary output, 5-pin
1
PINK/WHITE
(-) 200mA FLEX RELAY CONTROL OUTPUT
2
ORANGE
(-) 200mA ACCESSORY OUTPUT
3
VIOLET
(-) 200mA STARTER OUTPUT
4
PINK
(-) 200mA IGNITION 1 OUTPUT
5
BLUE
(-) 200mA STATUS OUTPUT


what of these wires should i connect to my car?

hi

anyone can help?