dei 555p w use for 03 focus
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=127051
Printed Date: May 16, 2024 at 11:28 AM
Topic: dei 555p w use for 03 focus
Posted By: zeekftw
Subject: dei 555p w use for 03 focus
Date Posted: April 21, 2011 at 5:33 PM
can i use dei 555p-w for 03 focus
Replies:
Posted By: blanx218
Date Posted: April 21, 2011 at 10:12 PM
I don't think it will work. The 555P is compatible with the older PATS systems. The 03 Focus has the newer Sentry type transponder.
Posted By: syl20rochon
Date Posted: April 21, 2011 at 10:34 PM
You'll need the 555UW or the PKFM. You can also use the Idata link ADSTB.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: howie ll
Date Posted: April 22, 2011 at 5:20 AM
The 555P was garbage.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: syl20rochon
Date Posted: April 22, 2011 at 7:56 AM
Not carbage but not the right application for your vehicle.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: howie ll
Date Posted: April 22, 2011 at 7:59 AM
Again Sy, apologies, we never had that much choice over here, either use a 556 or remove the RFI chip, it didn't matter because we were installing the R/S with a Cat 1 alarm with 2 cuts any way.
I think the cursed unit was the 555F for Ford and supposedly Toyota.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: syl20rochon
Date Posted: April 22, 2011 at 8:10 AM
When the open state door trigger came out, my first one came back because the gem was falling asleep, that is why I recommend the diodes. I also think that dei made a module for it, I think that I saw that.
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: syl20rochon
Date Posted: April 22, 2011 at 8:17 AM
Found the module...the DTIMAZDA is a open state door module interface...look it up
-------------
Sylvain Rochon
MECP security specialist
Tech support for remote starters
26 Years of experience counts
I'm here to help.
Posted By: howie ll
Date Posted: April 22, 2011 at 8:22 AM
Not that one, that's for Mazdas and late Fords using the open circuit door pins, completely different kettle of fish.
You can also use a step up resister or a relay for the same purpose but frankly the diodes whilst fiddly are much cheaper, especially if like me you buy 200 at a time.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
|