dei 530t
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=127517
Printed Date: May 12, 2024 at 3:03 AM
Topic: dei 530t
Posted By: 87rewire
Subject: dei 530t
Date Posted: June 01, 2011 at 2:06 PM
I have a question about the DEI 530T module wiring. I am trying to plan out my wiring before I do any hands on work. My question is about the auxillary channel and the ground when armed channel. The manual states that these wires need a negative input. I am wondering if the module needs a constant negative input or a pulsed negative input. What would happen if the negative input was constant to either of these wires. Thanks for the help.
Replies:
Posted By: Mark Mizenko
Date Posted: June 01, 2011 at 3:05 PM
The armed wire will start rolling the windows up when it receives a ground, if the ground latches, it will roll them all the way up and then stop.
If you pulse the aux before latching armed, it will leave the windows down. If armed is latched, and you pulse aux, it will vent the windows, if you latch aux, it will roll the windows down.
So it would be ok to latch Armed, but you would want Aux to just be pulsed (most likely)
Posted By: 87rewire
Date Posted: June 01, 2011 at 4:49 PM
ok thanks. That gives me a better idea what to do. I might need to find a way to switch a constant negative to a pulsed negative for the 530t.
Posted By: howie ll
Date Posted: June 01, 2011 at 5:43 PM
If you pulse it you will have to hold the button, also wire directly to each pair of motor wires if you want one-touch up and down from every switch.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: 87rewire
Date Posted: June 01, 2011 at 5:49 PM
Yes I definantly want the one touch up and down feature. I want to trigger the module with a door latch mechanism. The door latch will latch the negative however and I'm not sure if that will give me the result i'm looking for. I want the windows to vent when I open the door and arm (or go up) when i close the door. All while retaining the one-touch feature.
Posted By: howie ll
Date Posted: June 01, 2011 at 5:59 PM
Assuming you have or are installing an alarm follow the instructions exactly
If you do, use the GWA wire as explained above, this will give you close on lock.
After that process is complete, press aux for 15 seconds, this will vent the windows, press again for about 3 seconds to completely open them thus making your vehicle quite insecure.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: 87rewire
Date Posted: June 01, 2011 at 7:39 PM
Ok. Thanks for the input.
Posted By: 87rewire
Date Posted: June 08, 2011 at 6:07 PM
The manual states that the Dei 530T cannot control a relay because it monitors the noise generated by the window motor. Can the 530T control a relay if it is monitoring the window motor in this configuration. I am only looking for one way motor operation in this diagram.
Posted By: 87rewire
Date Posted: June 09, 2011 at 1:06 PM
Mods must have combined threads. Looking for an answer on the above post with diagram not the original topic at the top of page. Can the 530t drive a relay in this configuration?
Posted By: howie ll
Date Posted: June 09, 2011 at 6:16 PM
This is doable without an alarm depending on your vehicle it would help if you gave us make model and year.
I neither know what you're trying to achieve with that relay or what it is supposed to do. You will need a 528t timer unit along with your 530t.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: 87rewire
Date Posted: June 09, 2011 at 7:31 PM
Thanks again for the reply. This is just a diagram I drew up on ms paint. The vehicle I am working on is a custom wiring project so there is no true vehicle diagram. I will be basing the design off a 2002 pontiac firebird. I plan on using the factory alarm and keyless entry system to trigger the 530t. I will use the trunk pop feature of the remote for the aux channel and the bcm i am using has a ground when armed output. Aux channel for vent and gwa for windows up alarm armed. You are correct in that I plan on using a 528t with this configuration. If appropriate i can draw up a complete diagram and submit it for review.
Posted By: howie ll
Date Posted: June 10, 2011 at 3:58 AM
Good, PM me with your email address, I'll run up a diagram sometime today and email it back to you, bare with me because I'm 5 hours ahead of the Eastern Seaboard.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
|