fob is goh frdpc2002

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=127805
Printed Date: May 20, 2024 at 6:33 AM

Topic: fob is goh frdpc2002

Posted By: kiss161
Subject: fob is goh frdpc2002
Date Posted: July 03, 2011 at 10:32 PM

i have a aftermarket remote start keyless entry system with remote GOH FRDPC2002 by code alarm ? how can i program a 2nd remote .. thx

-------------
mark panncher

Replies:

Posted By: kiss161
Date Posted: July 04, 2011 at 2:57 PM

anyone?

-------------
mark panncher

Posted By: lectricguy
Date Posted: July 04, 2011 at 3:26 PM

Here is the general procedure for Code Transmitter programming:

TO PROGRAM ADDITIONAL TRANSMITTERS:

1) Enter the vehicle, and turn the ignition switch to the ON position.

2) Press and release the Programming button switch 3 times.

3) Press and hold the LOCK button of the transmitter you wish to program.

4) The lights will flash 1 time, indicating that the system is accepting the programming of channel #1 which

is lock.

"Repeat step 3 for each transmitter you wish to program"

5) Press and release the valet push button switch 1 time to advance to channel 2.

6) Press and hold the UNLOCK button of the transmitter you wish to program.

7) The lights will flash 1 time, indicating that the system is accepting the programming of channel #2 which

is unlock.

"Repeat step 6 for each transmitter you wish to program"

8) Press and release the valet push button switch 1 time to advance to channel 3.

9) Press and hold the TRUNK button of the transmitter you wish to program.

10) The lights will flash 1 time, indicating that the system is accepting the programming of channel #3 which

is trunk.

"Repeat step 9 for each transmitter you wish to program"

11) Press and release the valet push button switch 1 time to advance to channel 4.

12) Press and hold the STAR button of the transmitter you wish to program.

13) The lights will flash 1 time, indicating that the system is accepting the programming of channel #4 which

is remote start.

"Repeat step 12 for each transmitter you wish to program"

-------------
Lectric Guy

Posted By: kiss161
Date Posted: July 04, 2011 at 5:33 PM

thx

https://p71interceptor.com/remotestart/powercode.jpg

here is diagram of the alarm

i have these wires hooked up so far

a-5 ground

a-1 parking light output

a-2 door lock output

a-4 battery

a-13 trunk

a-14 door unlock output

so if i turn the key to ON position to try to program it wont work ..

what wire should i hook up so the box sees that the key is in the on position

then i can try to program 2nd remote

-------------
mark panncher

Posted By: lectricguy
Date Posted: July 04, 2011 at 8:38 PM

A7-Ignition 1 input/output. This wire acts as an input for programming. It should be connected to the vehicle's ignition wire, which will supply 12V when the key is in the "on" position.

-------------
Lectric Guy

Posted By: kiss161
Date Posted: July 04, 2011 at 9:11 PM

either one?

Ignition Positive Wire (+): Pink
Ignition Positive Wire Location: Ignition Switch Harness
Second Ignition Positive Wire (+): Green
Second Ignition Positive Wire Location: Ignition Switch Harness

-------------
mark panncher

Posted By: lectricguy
Date Posted: July 04, 2011 at 9:20 PM

The A7 wire, Ignition 1 input/output (Pink). This wire acts as an input for programming, or an output when the remote starter is used.

This wire from the Code system connects to the vehicle's ignition wire in the Ignition Switch Harness.

This wire is not interchangeable with the ignition 2 wire of the Code system for use as a programming input--only the A-7 pink wire will work.

-------------
Lectric Guy