wiring on 2008 ford econoline
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=128019
Printed Date: May 11, 2024 at 4:30 PM
Topic: wiring on 2008 ford econoline
Posted By: rookie01
Subject: wiring on 2008 ford econoline
Date Posted: July 23, 2011 at 8:22 PM
hello i am going to install a viper 5902 on a 2008 ford econoline, i am bit confused with the remote start harness wires, i am used to the older harness with all the relays and little better installation guide. can some one please tell me where to connect the wires for this harness.
thanks for any help or suggestions.
Replies:
Posted By: smokeman1
Date Posted: July 23, 2011 at 9:59 PM
Rather easy install. I did one on my work van E150. Web site below for wiring guide.
H3/2 RED / White, & H3/6 Red & H3/9 RED / Black to 12 Volts constant, H3/1 Pink to Ignition 1, H3/3 Orange to Accessory 1, H3/7 Pink/White to Accessory 2, H3/4 to starter side of cut starter wire, H3/5 to starter side of cut starter wire. Or just H3/5 to starter wire, (uncut).
https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: rookie01
Date Posted: July 24, 2011 at 5:59 PM
smokeman1 wrote:
Rather easy install. I did one on my work van E150. Web site below for wiring guide.
H3/2 RED / White, & H3/6 Red & H3/9 RED / Black to 12 Volts constant, H3/1 Pink to Ignition 1, H3/3 Orange to Accessory 1, H3/7 Pink/White to Accessory 2, H3/4 to starter side of cut starter wire, H3/5 to starter side of cut starter wire. Or just H3/5 to starter wire, (uncut).
https://www.bulldogsecurity.com/bdnew/vehiclewiringdiagrams.asp
thank you much i got the remote start working fine.
but my parking lights when arming the system doesn't flash. i connect the white wire from the alarm to the brown wire in the vehicle. is there another wire need to be connected with these new alarms. can anyone be of assistance.thanks
Posted By: smokeman1
Date Posted: July 24, 2011 at 7:02 PM
My first guess would be, did you install the 10amp mini fuse that is located under the cover of the brain? It looks like a door in the middle of the brain, slides up. make sure to check the polarity before inserting.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: rookie01
Date Posted: July 25, 2011 at 8:24 PM
smokeman1 wrote:
My first guess would be, did you install the 10amp mini fuse that is located under the cover of the brain? It looks like a door in the middle of the brain, slides up. make sure to check the polarity before inserting.
thanks yep got it to work. do you know the default number of times to press the valet switch to put the alarm in valet mode. and how do i change it. thanks again
Posted By: smokeman1
Date Posted: July 25, 2011 at 8:46 PM
Press the "F" button twice, the press the unlock button. Blue light on the antenna should stay on solid in valet mode. Press "F" button twice, press the unlock button to take it out of valet mode. Blue light on antenna should go out.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: rookie01
Date Posted: July 25, 2011 at 9:09 PM
smokeman1 wrote:
Press the "F" button twice, the press the unlock button. Blue light on the antenna should stay on solid in valet mode. Press "F" button twice, press the unlock button to take it out of valet mode. Blue light on antenna should go out.
thanks i know about that way i was wondering what if i dont have the remote and want to do it by the valet on the control center.
|