1999 dodge ram autopage remote starter.
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=128559
Printed Date: May 05, 2024 at 7:05 PM
Topic: 1999 dodge ram autopage remote starter.
Posted By: trae08
Subject: 1999 dodge ram autopage remote starter.
Date Posted: September 18, 2011 at 9:27 PM
I have a 1999 dodge ram 1500 and a recently purchased autopage C3-RS-603
I will begin installation in a few days but i have 1 question before i start and may have more after i start.
According to this chart
https://www.the12volt.com/installbay/alarmdetail/93.html
I need to use an additional relay to tie into The started wire with my remote start system. Is this correct?
Replies:
Posted By: Twelvoltz
Date Posted: September 18, 2011 at 9:39 PM
Neither DEI nor Audiovox show an additional relay requirement for that starter wire. I can't recall ever needing one in a 99 Ram either. The truck does have two accessory wires that need to be energized but only one standard starter wire. Head over to Audiovox's Tech Site and sign up for a free account. They offer their wiring information for free. I always check multiple wiring charts from every source I can before starting on a vehicle I have not yet done. Wiring charts are for reference only and all circuits need to be verified with a DMM prior to hooking in. ------------- Installer, IT support, and FFL. I need less hobbies.
Posted By: trae08
Date Posted: September 18, 2011 at 9:44 PM
Also what is the best way to tie into a wire?
Posted By: Twelvoltz
Date Posted: September 18, 2011 at 9:59 PM
Solder. Others may disagree, but solder is the ONLY thing I use. Search this forum there is a pretty good 'how to solder' write up.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: trae08
Date Posted: September 18, 2011 at 10:30 PM
2 accessory's? are you sure about that? im showing 2 ignition wires but only 1 accessory.
Posted By: Twelvoltz
Date Posted: September 19, 2011 at 7:07 PM
DEI shows the BLACK/ white as accessory...Audiovox lists it as ignition. As always, verify all wiring with a DMM before hooking up anything.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: trae08
Date Posted: September 19, 2011 at 7:40 PM
Alright. How do i verify a wire as being accessory or ignition with a multimeter?
Is there a method of how to test wires?
Posted By: trae08
Date Posted: September 20, 2011 at 12:30 AM
How do i strip a wire without cutting it?
i found this thread but all the pictures are gone. I dont want to use a razor blade ive done it that way before and always cut strands.
https://www.the12volt.com/installbay/forum_posts.asp~TID~56059~KW~oonikfraleyoo~PN~1~TPN~2
Posted By: trae08
Date Posted: September 20, 2011 at 10:17 PM
I need a little help, I got everything wired up except the 10 pin wire harness. Im not sure where to go with some of these wires.
any help would be greatly appreciated.
In that link its the
H3 – 8 White Connector Harness
https://www.autopageusa.com/resources/RS603%20INSTALLATION%20MANUAL7908.pdf
Posted By: trae08
Date Posted: September 22, 2011 at 7:17 PM
Ok, i got it all hooked up. it works great, But now my check engine light is on and the autopart store says there are no codes to read.
|