adding door lock actuators to 96 integra
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=129350
Printed Date: July 15, 2025 at 1:25 AM
Topic: adding door lock actuators to 96 integra
Posted By: shadow818
Subject: adding door lock actuators to 96 integra
Date Posted: November 23, 2011 at 1:49 PM
ok guys i picked up 2 actuators but they have the 5 wires coming out of them and im installing them in a 96 integra that doesnt have power locks can i still wire this actuators for the 2 wire reverse polarity? the actuators ars scosche dla1 let me know if not so i can return them
Replies:
Posted By: shadow818
Date Posted: November 23, 2011 at 4:47 PM
Ok I'm using the autopage rf-425 for this setup and it seems like I can add the actuators with the onboard relays Can anyone verify this ?
Posted By: howie ll
Date Posted: November 23, 2011 at 5:18 PM
Yes for the two wire, (green and blue?).
How many lock wires does the Autopage have, 2 or 6?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: howie ll
Date Posted: November 23, 2011 at 5:24 PM
Page 8 of the install guide, "adding actuators".
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: shadow818
Date Posted: November 23, 2011 at 8:38 PM
Correct I saw that so that means if I use the 6 wire harness I don't need to do it with any relays correct?
Posted By: howie ll
Date Posted: November 24, 2011 at 1:22 AM
Yes.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: shadow818
Date Posted: December 18, 2011 at 2:19 PM
Now how can I add a lock unlock switch and connect to the alarm ?
Posted By: howie ll
Date Posted: December 18, 2011 at 2:45 PM
Use a 5 pin window switch from Spal, green and blue to outer terminals negs (grounds) to next two and 12v+ constant, 15amps fuse to centre pin.
Why would you need a switch if you have remote control (keyless entry) and possibly ignition lock/unlock from the Autopage?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: howie ll
Date Posted: December 18, 2011 at 3:21 PM
Scratch my last answer ref: the switch.
Centre pin, 12v+ constant fused at 15amps.
Next green lock motor wire from R/S then green to solenoids from outer.
Other side, blue or unlock motor wire from R/S, outer blue to solenoids.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: shadow818
Date Posted: December 18, 2011 at 4:34 PM
It doesn't let my keyless unlock or lock when the ignition is on and no switch to lock unlock from the inside looking for the easiest way to add a switch to the keyless alarm
Posted By: shadow818
Date Posted: December 20, 2011 at 9:08 PM
Howie can't I just use a lock spal illuminated switch to provide neg pulse to lock unlock?
howie ll wrote:
Scratch my last answer ref: the switch.
Centre pin, 12v+ constant fused at 15amps.
Next green lock motor wire from R/S then green to solenoids from outer.
Other side, blue or unlock motor wire from R/S, outer blue to solenoids.
Posted By: howie ll
Date Posted: December 20, 2011 at 11:01 PM
No. You are using the motor wires from the alarm. Adding negatives won't work you would need two more relays. Simply feeding pos will blow a fuse every time you use the switch.
If SPAL does a switch marked lock with the 5 pin configuration then it's wired as I explained.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
|