2011 toyota 4 runner
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=130133
Printed Date: May 15, 2024 at 4:44 PM
Topic: 2011 toyota 4 runner
Posted By: casale33
Subject: 2011 toyota 4 runner
Date Posted: January 09, 2012 at 8:41 PM
was wondering i have a python rs and alarm disarm wire also unlocks door but stays open any wiring to relock the doors during remote start
Replies:
Posted By: Twelvoltz
Date Posted: January 09, 2012 at 8:47 PM
This is a PTS 4Runner? If it's regular key then the keysense wire will disarm the factory alarm.
What model Python RS are you installing?
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: casale33
Date Posted: January 09, 2012 at 8:51 PM
its a python 413 with a 556u module install door unlock are hooked up has factory alarm
Posted By: Twelvoltz
Date Posted: January 09, 2012 at 8:58 PM
Do you use a regular key to start the vehicle or does it have Push To Start (PTS)?
What did you use to disarm the factory alarm? Did you use the disarm output from the Python or did you use the door unlock output and set it to double pulse?
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: casale33
Date Posted: January 09, 2012 at 9:01 PM
sorry regular key , without the disarm wire hooked up when i hit remote start button the alarm sounded
Posted By: casale33
Date Posted: January 09, 2012 at 9:04 PM
unless i unlocked the doors before remote start then the alarm did not sound off
Posted By: Twelvoltz
Date Posted: January 09, 2012 at 9:09 PM
Use the second status output wire, whichever one you didn't use to activate the 556U (either the blue or the blue/white) hooked to the vehicle's keysense wire (black). It will disarm the factory alarm when remote starting.
-------------
Installer, IT support, and FFL. I need less hobbies.
Posted By: casale33
Date Posted: January 09, 2012 at 9:17 PM
yes was thinking of doing something with the 2nd status wire but im confused about the key sense wire the schematic for truck says n/a for key sense
Posted By: Chris Luongo
Date Posted: January 10, 2012 at 6:16 AM
It definitely does have keysense.
Just go in there and test the wires around the keyswitch until you find it. Look for a two-pin connector with one WHITE/ black and one other color.....the other color should be keysense.
Put either your blue/white status or blue ground-while-running from the Python to the keysense wire in the car.
Posted By: casale33
Date Posted: January 10, 2012 at 7:12 AM
Ok thanks I will try this later. Should I then disconnect. The alarm disarm wire from python so the locks wont unlock on remote start? And how should i program the blue 2nd activation wire pulse or constant , I used the blu/ white for 556 u activate
Posted By: casale33
Date Posted: January 10, 2012 at 4:41 PM
sorry i used the blue for activation of the 556u and ill use the blue/white for second activation which would be programed normal mode..
Posted By: casale33
Date Posted: January 21, 2012 at 4:19 PM
just wondering, i want to install tach wire instead of virtual tach truck keeps on not starting on first try is data link conn the same as the OBD11 or do i have to run wire to the injector thanks
Posted By: Mike M2
Date Posted: January 22, 2012 at 8:05 AM
Yes, the OBD2 is the correct location under the dash.
Also, you do want to disconnect the disarm wire. Only the keysense is needed. ------------- Mike M2
Tech Manager
CS Dealer Services
Posted By: casale33
Date Posted: February 17, 2012 at 4:01 PM
thank, sorry for the slow reply. everything worked great
|