Print Page | Close Window

python 323 on a 1996 ex

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=130199
Printed Date: May 20, 2024 at 2:03 PM


Topic: python 323 on a 1996 ex

Posted By: sonicgroovesi
Subject: python 323 on a 1996 ex
Date Posted: January 13, 2012 at 9:11 PM

I have been searching on tips about installing this alarm I came across a post of a member that goes by superden. Hes installing his 323 in an 2004 HONDA CRV and the wiring schematics are the same as my 1996 civic. Now superden put a link up to the schematic of the way he was hooking up his i was wondering if someone could double check this link and let me know if its right. Especially the part about the door locks any help would be appreciated considering this is my first alarm install in like 10 years and a lot has changed since then. All my old friends have talked me up to my wife about how good i was when it came to tricking out cars (mainly in the performance dept) and im trying not to disappoint her or make her think my friends exaggerated a bit to make me look good to her before we married. Heres a link to the schematic pdf: in question. https://www.slideshare.net/superden001/excel-worksheet-9691324
and again thanks a head of time



Replies:

Posted By: sonicgroovesi
Date Posted: January 13, 2012 at 11:08 PM
hers his schematicts typed out in case anybody found it hard to read the link
PYTHON 323 ON 2004 HONDA CR-V     
     
H-1:MAIN HARNESS     
ALARM WIRE COLOR / CAR WIRE COLOR      

1     (-) 200mA TRUNK RELEASE OUTPUT     RED / WHITE      BLACK / YELLOW (-)     
2     (+) 12VDC CONSTANT INPUT      REDWHITE     
3     (+) SIREN OUTPUT             BROWNSiren( +) wire     
4        PARKING LIGHT ISOLATION
      WIRE-PIN 87a OF ONBOARD RELAY     WHITE/ BROWN      X     
5     (-)CHASSIS GROUND              BLACKGround to Chassis     
6     (+)DOOR TRIGGER INPUT             VIOLET        X     
7     (-)TRUNK PIN/INSTANT TRIGGER
     INPUT (NC or NO)      BLUEGREEN / WHITE (-)     
8     (-)DOOR TRIGGER     DR.:GREEN(-)DIODE Isolate
     INPUT (NC or NO)     GREENPAS.&REAR:GREEN/ RED(-)     
9     FLEX RELAY OUTPUT             BLACK/ WHITE      X     
10     (-) 200mA AUX1 OUTPUT             WHITE/ BLUE      X     
11     PARKING LIGHT OUTPUT             WHITERED / YELLOW (+)      
12     (-) 500mA GROUND WHEN
    ARMED OUTPUT      ORANGEGROUND(-)     
     
H-2:DOOR LOCK HARNESS     
1     UNLOCK #87 NORMALLY OPEN(INPUT) VIOLETGROUND (-)     
2     UNLOCK #30 COMMON (OUTPUT)      BLUE/BLACK      WHITE/ GREEN      
3     UNLOCK #87a NORMALLY CLOSED     BROWN / BLACK      X     
4     LOCK #87 NORMALLY OPEN (INPUT)     VIOLET/BLACK      GROUND (-)     
5     LOCK #30 COMMON (OUTPUT)     GREEN/ BLACK      WHITE/ BLUE     
6     LOCK #87a NORMALLY CLOSED     WHITE/ BLACK      X     
7     FLEX RELAY #87 NORMALLY OPEN     WHITE/ VIOLET      X     
8     FLEX RELAY #87a NORMALLY CLOSED     WHITE/ BROWN      X     
PYTHON 323 ON 2004 HONDA CR-V     
     
H-1:MAIN HARNESS     
ALARM WIRE COLOR / CAR WIRE COLOR      

1     (-) 200mA TRUNK RELEASE OUTPUT     RED / WHITE      BLACK / YELLOW (-)     
2     (+) 12VDC CONSTANT INPUT      REDWHITE     
3     (+) SIREN OUTPUT             BROWNSiren( +) wire     
4        PARKING LIGHT ISOLATION
      WIRE-PIN 87a OF ONBOARD RELAY     WHITE/ BROWN      X     
5     (-)CHASSIS GROUND              BLACKGround to Chassis     
6     (+)DOOR TRIGGER INPUT             VIOLET        X     
7     (-)TRUNK PIN/INSTANT TRIGGER
     INPUT (NC or NO)      BLUEGREEN / WHITE (-)     
8     (-)DOOR TRIGGER     DR.:GREEN(-)DIODE Isolate
     INPUT (NC or NO)     GREENPAS.&REAR:GREEN/ RED(-)     
9     FLEX RELAY OUTPUT             BLACK/ WHITE      X     
10     (-) 200mA AUX1 OUTPUT             WHITE/ BLUE      X     
11     PARKING LIGHT OUTPUT             WHITERED / YELLOW (+)      
12     (-) 500mA GROUND WHEN
    ARMED OUTPUT      ORANGEGROUND(-)     
     
H-2:DOOR LOCK HARNESS     
1     UNLOCK #87 NORMALLY OPEN(INPUT) VIOLETGROUND (-)     
2     UNLOCK #30 COMMON (OUTPUT)      BLUE/BLACK      WHITE/ GREEN      
3     UNLOCK #87a NORMALLY CLOSED     BROWN / BLACK      X     
4     LOCK #87 NORMALLY OPEN (INPUT)     VIOLET/BLACK      GROUND (-)     
5     LOCK #30 COMMON (OUTPUT)     GREEN/ BLACK      WHITE/ BLUE     
6     LOCK #87a NORMALLY CLOSED     WHITE/ BLACK      X     
7     FLEX RELAY #87 NORMALLY OPEN     WHITE/ VIOLET      X     
8     FLEX RELAY #87a NORMALLY CLOSED     WHITE/ BROWN      x   
     
STARTER KILL HARNESS      
"BLACK / WHITE wire, located under dash at FUSE / RELAY BOX Starter "     
Wire Must Be Accessed After Fuse Block To Prevent Check Engine Light.
Cut BLACK/ WHITE wire & connect as directed.     

1     STARTER-COMMON (KEY SIDE)          GREEN / WHITE   KEY SIDE BLACK/ WHITE     
2     STARTER-NORMALLY OPEN(MOTOR SIDE)    GREEN        MOTOR SIDE BLACK/ WHITE      
3     STARTER-NORMALLY CLOSED(MOTOR SIDE) GREEN/ BLACK   X       
     
STARTER KILL HARNESS      
"BLACK / WHITE wire, located under dash at FUSE / RELAY BOX Starter "     
Wire Must Be Accessed After Fuse Block To Prevent Check Engine Light.
Cut BLACK/ WHITE wire & connect as directed.     

1     STARTER-COMMON (KEY SIDE)          GREEN / WHITE   KEY SIDE BLACK/ WHITE     
2     STARTER-NORMALLY OPEN(MOTOR SIDE)    GREEN        MOTOR SIDE BLACK/ WHITE      
3     STARTER-NORMALLY CLOSED(MOTOR SIDE) GREEN/ BLACK   X




Posted By: yesk13
Date Posted: January 14, 2012 at 3:49 PM
I also have the Python 323 hooked everything up, but got no respond from the module. the module did receive power to it and the valet/command center does have 5v but no LED light from it. My next try is to disconnect everything and connect the H1/2 and H1/5 to battery with the command switch to see if i get anything. if not i'll have to return it.




Posted By: howie ll
Date Posted: January 14, 2012 at 4:48 PM
First post, you have everything correct but obviously don't assume, test.
Starter cut,use GREEN/ black not green, it's inherently safer.
Second poster, recheck your wiring. These units almost never go wrong.

-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.




Posted By: sonicgroovesi
Date Posted: January 14, 2012 at 5:37 PM
thanks for your response my wife gets to bring the car home on the26 guess ill be going ahead with the install wanted to get as much info on this installed before the car comes home don't want to give any one a chance to steal the car a civic was just stolen right over here a couple of weeks ago.i bet you'll see me on here a lot more   thanks.




Posted By: sonicgroovesi
Date Posted: January 14, 2012 at 5:56 PM
Hey Howie iv'e got one ? that bugs me still on the H2 harness can you please explain to me why the H2/2 2 UNLOCK #30 COMMON (OUTPUT)      BLUE/BLACK wire goes to the cars WHITE/ GREEN power lock wire i kind of figured the alarms unlock wire would go to the cars unlock wire?i just find that strange but with all i don't know about alarms im extremly curious.plus if it isnt to much trouble how do you hook up the dome light security in case the wife would like that hooked up also thanks




Posted By: howie ll
Date Posted: January 14, 2012 at 6:16 PM
Just read my signature line!

-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.




Posted By: yesk13
Date Posted: January 14, 2012 at 6:42 PM
i'll explain the WHITE/ green to unlock 30 common once i get home, i'll show you the wire diagram. i could even youtube it.




Posted By: sonicgroovesi
Date Posted: January 14, 2012 at 7:06 PM
killer always trying to learn something new




Posted By: yesk13
Date Posted: January 14, 2012 at 9:21 PM
sorry, have to wait till next day or monday. i have to double check the wire color of my H2 to door lock first.




Posted By: sonicgroovesi
Date Posted: January 14, 2012 at 10:38 PM
no prob wont be doing anything till the 26th anyway




Posted By: sonicgroovesi
Date Posted: January 15, 2012 at 6:42 PM
yesk13 wrote:

I also have the Python 323 hooked everything up, but got no respond from the module. the module did receive power to it and the valet/command center does have 5v but no LED light from it. My next try is to disconnect everything and connect the H1/2 and H1/5 to battery with the command switch to see if i get anything. if not i'll have to return it.
Did you ever get this straighten out ?




Posted By: yesk13
Date Posted: January 15, 2012 at 8:10 PM
ya, i got the alarm working. only got the rear two doors and trunk hooked up to trigger alarm. no parking light flash when i arm or disarm, i need to check it again. the unlock and lock works, and don't connect the unlock to the alarm's lock wire. unless you want to play a joke to your wife. When she arm the alarm it will unlock and when she disarm the alarm the door will lock, lol.




Posted By: sonicgroovesi
Date Posted: January 15, 2012 at 9:24 PM
thats what i figured about the lock/unlock i did a mock hook up on mine with a battery i had laying around used a test light as a parking light substitute i actually forgot to put the fuse in the brain for the lights first but then remembered it





Print Page | Close Window