compustar, blade, add ons
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=130226
Printed Date: May 02, 2024 at 6:06 AM
Topic: compustar, blade, add ons
Posted By: trafficbuck
Subject: compustar, blade, add ons
Date Posted: January 15, 2012 at 4:31 PM
I have (2) of these systems Compustar FT-6000AS, RPS Touch, temp sensor, dual shock sensor and the Blade TB (module/bypass) loaded with the correct firmware for each vehicle. I have access to load and set the options via idatalink, I also have the Option Programer CM3-series.
One is going in a 2005 Chrvy Silverado SS & the other in a 2000 GMC Jimmy SLT
Please help with thie wiring instructions using the Blade (module/bypass) I'm having a hard time finding clear instructions to wire with the blade on both vehicles.
I would like to add the voice with (2) motion sensors in each vehicle. Please help with how to wire them in and the best brand model.
Do I need extra modules to have the option to controll from the remote roll up/down windows, AC, heat, Defrost ect. ?
Please let me know the best add ons for these systems & how to wire them in.
Replies:
Posted By: trafficbuck
Date Posted: January 15, 2012 at 4:43 PM
I'm considering the add on of Compustar EZ GO.
They seem to be very handy allowing the vehicle to unlock when you approach within 3 feet...
Is any one experienced with these?
Posted By: offroadzj
Date Posted: January 15, 2012 at 5:43 PM
The blade-AL would have been better on the silverado because it is a data bypass and would control many more functions than just the immobilizer. With that said, here is the directions.
The only wire connection from the blade harness for both vehicles is the orange data wire which will go to pin 2 of the obdii port.
For programming, you just have to put the key in the ignition, turn the ignition on, then start the vehicle and watch the LED on the blade. It should illuminate green for 2 seconds if module programming was successful.
-------------
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
Posted By: trafficbuck
Date Posted: January 15, 2012 at 6:37 PM
Thank you for the prompt reply...
Sorry, I forgot to add the type of Blade for the Silverado is the AL
So on both vehicles I only need the orange data wire to go to pin 2 of the obdii port ?
Would that be the only one wire from the blade connector?
I am having a hard time realizing that???
I'm a noob sorry im new at this...
So would not even need to connect the CN1 (white) 6P Power Connector?
Any advice on my other questions?
Posted By: offroadzj
Date Posted: January 15, 2012 at 6:43 PM
The orange connection is the only connection for the blade connector. The other connections on the unit still need to be made (main ignition connections, parking lights, ground, hood pin, etc)
-------------
Kenny
Owner / Technician
KKD Garage LLC
Albany, NY 12205
Posted By: trafficbuck
Date Posted: January 15, 2012 at 7:34 PM
Compustar FT-6000AS, RPS Touch, temp sensor, dual shock sensor and the Blade TB (module/bypass) loaded with the correct firmware for each vehicle. I have access to load and set the options via idatalink, I also have the 2000 GMC Jimmy SLT
I would like to add the voice with (2) motion sensors. Please help with how to wire them in and the best brand model.
Do I need extra modules to have the option to controll from the remote roll up/down windows, AC, heat, Defrost ect. ?
Please let me know the best add ons for these systems & how to wire them in.
Posted By: tedmond
Date Posted: January 15, 2012 at 10:36 PM
No need for ft ez go, just turn on international 2 way mode and you have proximity lock and unlock. Motion sensor, use the 4pin green connector and wire up the aftermarket sensors to that harness.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: tedmond
Date Posted: January 15, 2012 at 10:44 PM
Defrost you Need the compustar op500 to program one poc connector for defrost
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: trafficbuck
Date Posted: January 16, 2012 at 11:22 AM
Thank you all for all the help/replies...
When adding 2 Motion sensor to the same brain do CM6000 would I tie them together and use the 4pin green connector?
I have currently have one aftermaket motion sensor but the plug does not match to plug into the CM6000 brain?
Where can you get all the add on connectors?
Please let me know what brands of add ons will connect to the CM6000 without having to purchase a connector for the CM6000 brain.
Posted By: tedmond
Date Posted: January 16, 2012 at 4:51 PM
yes you would tie both together using the 4 pin green harness.
you will place diodes inline to isolate each sensor. this should be outlined in the manual.
-------------
Ted
2nd Year Tier 1 Medical School
Still installing as a hobby...pays for groceries
Compustar Expert
Posted By: TooDark
Date Posted: February 21, 2012 at 4:21 PM
tedmond wrote:
No need for ft ez go, just turn on international 2 way mode and you have proximity lock and unlock. Motion sensor, use the 4pin green connector and wire up the aftermarket sensors to that harness.
How do I turn on international 2 way mode? How does the proximity sensor work buy only turning on this mode?
|