508d compatible with the viper 5704?
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=132692
Printed Date: May 15, 2024 at 7:43 PM
Topic: 508d compatible with the viper 5704?
Posted By: lilflippy
Subject: 508d compatible with the viper 5704?
Date Posted: November 17, 2012 at 4:50 AM
Hi I have this the Viper 5704 and ordered a 508D Dual-Zone Radar Sensor.
I was reading in the install manual that Sensor ports 1 and 2 cannot support sensor 508D due to current limitations. These ports are also
constant power and ground connections.
How would the 508D hook up to my system?
Please reply back thanks?
Replies:
Posted By: howie ll
Date Posted: November 17, 2012 at 6:49 AM
The answer is so simple, run the power to the red feed and the ground to the regular ground.
You must held the record for silly posts with obvious answers and yes Kregg if you read this the blood pressure has started to climb.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: lilflippy
Date Posted: November 17, 2012 at 9:14 AM
howie ll wrote:
The answer is so simple, run the power to the red feed and the ground to the regular ground.
You must held the record for silly posts with obvious answers and yes Kregg if you read this the blood pressure has started to climb.
OK kool. And I can just plug.the.green and.blue.wire to the empty sensor.port right?
Posted By: howie ll
Date Posted: November 17, 2012 at 9:20 AM
Yes.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: lilflippy
Date Posted: November 17, 2012 at 7:17 PM
What would happen if I plugged it into one of the sensor ports?
Posted By: howie ll
Date Posted: November 17, 2012 at 11:08 PM
Try it and let me know.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: lilflippy
Date Posted: November 18, 2012 at 6:58 PM
howie ll wrote:
Try it and let me know.
Update so I connected the 4 pin to one of empty sensor ports and it work. Now I just have to adjust and tweak it.
I mounted it the middle of my overhead console. Would that be the best position for this sensor?
Posted By: howie ll
Date Posted: November 19, 2012 at 1:36 AM
YES.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: mosesaro
Date Posted: July 13, 2013 at 9:27 PM
lilflippy wrote:
What would happen if I plugged it into one of the sensor ports?
lilflippy how did you installation of the 508D with 5704 go. Does it work if you just plug it in directly?
Posted By: lilflippy
Date Posted: July 14, 2013 at 9:40 AM
mosesaro wrote:
lilflippy wrote:
What would happen if I plugged it into one of the sensor ports?
lilflippy how did you installation of the 508D with 5704 go. Does it work if you just plug it in directly?
Hi Yes I just plug it in and it works.
|