tacoma python alarm
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=132779
Printed Date: May 02, 2025 at 6:33 AM
Topic: tacoma python alarm
Posted By: rsecco
Subject: tacoma python alarm
Date Posted: November 24, 2012 at 7:21 PM
Hello
I just install a Python 574 in a 2013 Toyota Tacoma..all is working well.but...
When I remote start..many ligh in the instruments panel still on..after I introduce the key in the lock all became normal only the air bag icon still on..what wrong?
a bad connection?
Thanks
Raul
Replies:
Posted By: howie ll
Date Posted: November 24, 2012 at 7:26 PM
Have you connected both the ignition wires?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: howie ll
Date Posted: November 24, 2012 at 7:27 PM
Does the air bag icon come on when you simply use the key?
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: rsecco
Date Posted: November 24, 2012 at 10:02 PM
Hello
Yes . both ignitions are conected..I didn't use anti-grid relay
Thanks
Raul
Posted By: rsecco
Date Posted: November 24, 2012 at 10:07 PM
Hello
Air bag icon still on when I use key after remote started .If i unplug H3 conector from the main module..and start with the key..all is normal. I didn't use any diode or relay in my conection..
Thanks
Raul
Posted By: howie ll
Date Posted: November 25, 2012 at 2:06 AM
Please list your wiring, H3 to car.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: rsecco
Date Posted: November 25, 2012 at 9:35 AM
Hello again
Here is the wiring
H3-1 Pink to BLACK/ Red (Ignition 1)
H3-2 RED / White to Not Connected
H3-3 Orange to WHITE/ Green (Accessory/Heating blower)
H3-4 Violet to GREEN/ Black and BLACK/ White (Starter 1 and 2)
H3-5 Green to Not Connected
H3-6 Red to WHITE/ Blue (12 volts Constant 50A ??)
H3-7 Pink/White to Blue / YELLOW (Ignition 2)
H3-8 Pink/Black to Not Connected
H3-9 RED / Black to WHITE/ Red (12 volts Constant 30A)
H3-10 n/a
Thanks
Raul
Posted By: howie ll
Date Posted: November 25, 2012 at 10:22 AM
OK
H3/2 RED / White That's one reason for the warning lights it won't start CONNECT.
Starter one, cut key side to H3/5,GREEN.
Starter side to H3/4 Violet.
Starter 2, use a relay and a diode (1N4004)as per the diagram:-
tac_2nd._starter.bmp
Diode use is MANDATORY to protect your R/S.
Wiring the two starters together as you've done is inviting trouble and expense down the road.
Why do you think some car manufacturers split those circuits?
And that's probably the second reason. ------------- Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: howie ll
Date Posted: November 25, 2012 at 11:21 AM
When all is done you will probably need to get the airbag warning light cleared.
-------------
Amateurs assume, don't test and have problems; pros test first. I am not a free install service.
Read the installation manual, do a search here or online for your vehicle wiring before posting.
Posted By: Mike M2
Date Posted: November 25, 2012 at 12:41 PM
Tacoma airbag light will go out if you disconnect the battery for 1 minute.
-------------
Mike M2
Tech Manager
CS Dealer Services
|
