iluminated entry 04 chevy silverado

Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=132803
Printed Date: August 26, 2025 at 7:43 AM

Topic: iluminated entry 04 chevy silverado

Posted By: pvcsilverado
Subject: iluminated entry 04 chevy silverado
Date Posted: November 27, 2012 at 10:01 AM

I recently installed a viper 5704 on a 04 silverado, i noticed that when the truck is running with the remte start and i unlock it the iluminated en =try does not come on like when the truck is not running, reverse light and DRL dont come on!is there some thing that i could do to make it come on when running?it has a DBALL

And also i noticed that my temp reading is alwayas at 86! dont know why.did i miss a wire tobe connected to the temp sensor??thank you!!

-------------
PVC

Replies:

Posted By: kreg357
Date Posted: November 27, 2012 at 12:58 PM

Please list your Viper H3 harness connections. posted_image

-------------
Soldering is fun!

Posted By: pvcsilverado
Date Posted: November 27, 2012 at 7:03 PM

Here s h3 connections;
h1pink ignition 1 to pink
h2red white ignition 2 to constant 12 volt
h3orange accesorry to orange
h4violet starter output to yellow starter
h5green starter input to yellow staterkey side
h6red ignition 1 input to 12 volt constant
h7pink/white ignition 2 to white
h8pink/black flex relay to none
h9red black accesory to 12 volt constant

-------------
PVC

Posted By: kreg357
Date Posted: November 27, 2012 at 7:29 PM

They look good. Not sure if it matters much on that truck but there is a Brown ACC2 wire.

Might try reprogramming the DB-ALL ( don't use them ). Next would be going to W2W ( if you're D2D now ) and as a last resort a call to Directed Tech Support.

-------------
Soldering is fun!

Posted By: pvcsilverado
Date Posted: November 27, 2012 at 7:54 PM

So the iluminated entry should come on when runnig??how about the H2 harness ,any connections that i mtight of missed on that?

also how about the temp ?any thughts on that?

-------------
PVC

Posted By: kreg357
Date Posted: November 27, 2012 at 8:29 PM

Not sure on your 2004 Silverado, haven't done any for a while. Most vehicles will turn on the interior lights with an unlock while the engine is off but not while it is running. You could try connecting the Vipers' Dome Light Supervision wire.

Dome Loght Supervision info from various sources ( they do conflict, so test ).

From Bulldog Security :
DOMELIGHT SUPERVISION GRAY/BLACK (-) @ BCM, BLACK PLUG, PIN E, SEE NOTE #3
NOTE #3: The BCM is located under the Drivers Side of the dash, the BCM has 6 plugs on it,
with the PURPLE plug on the back.

From ReadyRemote :
Dome Supervision gray/black (+) @ BCM, black plug, pin E

From AudioVox :
Domelight Super USE ONE DOOR TRIGGER (+) IN HARNESS AT VEHICLE DOMELIGHT

From Omega :
Dome Light DR (-) GY/BK,PAS (-) BLK/WHT AT BCM (BLUE 24 PIN CONN) *

Viper:
H2/7 BLACK / YELLOW (-) 200mA DOME LIGHT SUPERVISION 0UTPUT

The Temp Gauge problem is strange. Are you sure it wasn't happening before the R/S install?

-------------
Soldering is fun!

Posted By: pvcsilverado
Date Posted: November 27, 2012 at 8:47 PM

Thank you Kreg!
ill connect the domelight!

About the temp gauge ,i did not notice until i was done with the install. since at day time it was around 86 i thugth it was normal

-------------
PVC

Posted By: ziggyb222
Date Posted: November 28, 2012 at 8:24 PM

There is a proceedure to re-calibrate those mirrors. I did it one time for a friend.. Google it, I am sure you will come up with the procedure...