viper 4103 d2d
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=133066
Printed Date: May 13, 2024 at 3:50 AM
Topic: viper 4103 d2d
Posted By: markc732
Subject: viper 4103 d2d
Date Posted: December 23, 2012 at 8:36 PM
i am installing a viper 4103 in a 2006 saturn vue i am trying to hook up a flashlogic flcan to d2d port it seems there isant no power to the flcan is there any wire that i have to hook up for it to have power and also the flcan manual says that the passlock wire is yellow in the same harness as everything else i can not find the yellow wire please i need help before christmas its a gift for my wife i have her car all torn apart
thank you and merry christmas
if you want you can text me
908-616-5483
Replies:
Posted By: shortcircuit161
Date Posted: December 23, 2012 at 9:04 PM
The passlock wires are usually by themselves coming from the ignition switch close to where you insert the key. There are 3 wires - yellow, black and white. The keysense wire (required) should also be close to the passlock wires.
Test the D2D port to see if you have 12v and ground going thru the red and black wires.
-------------
Posted By: markc732
Date Posted: December 23, 2012 at 9:41 PM
i tested the black and red coming out of my auto start brain and there is no power i hooked up the flcan to 12 volts and ground with the wires provided and it comes on is there a setting that i have to turn on
Posted By: dasbogie
Date Posted: December 23, 2012 at 10:39 PM
the viper brain might be in esp mode. disconnect power harness from viper. take the WHITE/ blue activation input and stuff it in the ground pin on the viper harness. reconnect the heavy gauge power harness and the led on the end of the viper should flash for 5 seconds which means it's now in d2d. remove WHITE/ blue from ground and insulate. reset your flcan and select mode, then program flcan
-------------
Advanced
Posted By: markc732
Date Posted: December 24, 2012 at 8:49 AM
i hooked the whit/blue to ground it flashed and still n o power coming out of the viper to the flcan
Posted By: shortcircuit161
Date Posted: December 24, 2012 at 9:11 AM
Whether the Avital is in ESP or D2D mode, that port should have power and ground coming thru it.
Are you using the correct D2D cable? Or did you build one? Did you test all 4 wires to see if any of them have 12v? It's possible the pinouts are wrong.
You can also just go W2W since it's only 5 wires you would need to replace for the D2D cable. 12v, ground, lock, unlock and GWR (status) output.
-------------
Posted By: markc732
Date Posted: December 24, 2012 at 2:44 PM
im going to try w2w now i will let you know do you know what color tach wire it is
Posted By: shortcircuit161
Date Posted: December 24, 2012 at 3:53 PM
On the Vue,
Tachometer - NOT pink or red - ac - any fuel injector
On the Avital, it's the violet/white wire on the shutdown harness (the same one with the brake wire).
-------------
Posted By: markc732
Date Posted: December 24, 2012 at 4:55 PM
i cant get this thing im giving up thanks for all your help
|