fl can and 2004 infinity g35
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=133280
Printed Date: July 06, 2025 at 11:56 PM
Topic: fl can and 2004 infinity g35
Posted By: the727kid
Subject: fl can and 2004 infinity g35
Date Posted: January 12, 2013 at 4:23 PM
I am installing remote start in my girlfriends 2004 Infinity G35. I can not get the FL Can to program properly for the life of me. It flashes colors at will it seems like. I have the rest of the system working perfect and the car attempts to crank but does not.
I did not use D2D and opted to hard wire everything. I have Ground/Power... Security Light, Can High and Can Low hooked up, as well as the ignition input tied into the ignition output from to the remote starter.
As I was typing this I realized I may need the Ground when Running Connected, can anyone confirm this? What would the ground when running connect to on the alarm? (Viper 5204V)
Replies:
Posted By: the727kid
Date Posted: January 12, 2013 at 4:31 PM
Actually cancel that on GWR, I actually did connect that to Status output.
Posted By: kreg357
Date Posted: January 12, 2013 at 4:32 PM
Yes GWR is necessary with W2W mode. Connect to the Viper Blue (-) 200mA Status Output wire.
A few questions...
Did you get the FLCAN flashed with the FLC-AL(DL)-NI1 firmware?
Did you set he FLCAN Installation Mode to Standard ( 2 blinks ) and lock it in? ------------- Soldering is fun!
Posted By: the727kid
Date Posted: January 12, 2013 at 4:33 PM
The light is currently flashing green with nothing in the car.
Posted By: the727kid
Date Posted: January 12, 2013 at 4:34 PM
Why can't I edit on this forum? Anyways it is flashing green no matter if key is in ignition or not.
Posted By: the727kid
Date Posted: January 12, 2013 at 4:34 PM
Yes FLCAN is flashed with the firmware. As far as standard mode... I think...
Posted By: kreg357
Date Posted: January 12, 2013 at 4:59 PM
Using Install Guide #5463 for the FLCAN flashed with FLC AL(DL) NI1 firmware.
Do the Factory Reset procedure as shown on Page 11, then continue on to the Install mode selection on the
top of Page 10 and then the actual vehicle programming on the middle of Page 10.
Please note that while it is not actually shown in the Type 3 diagram, the R/S's Ignition1 wire also goes to the
G35's BLACK/ Red Ignition wire. The FLCAN must see its' Ignition input wire go to +12V to initiate programming. ------------- Soldering is fun!
Posted By: the727kid
Date Posted: January 12, 2013 at 5:24 PM
Correct, I do have it to the Pink Ign 1. I will try factory resetting and programming again. Thank you for your help so far.
Posted By: the727kid
Date Posted: January 12, 2013 at 5:45 PM
Ok I played with it in some odd sequence (which made no sense with what the directions said) and it started. Now the car turns on then shuts off. I am thinking I just need to just adjust the tach mode.
For hardwired tach should it be set to voltage (option 2) or tach (option 4)? Virtual tach is 1 and nothing for option 3.
Posted By: the727kid
Date Posted: January 12, 2013 at 6:04 PM
Well I tried shutdown diagnostics and it will not give me any LED flashes.
Posted By: kreg357
Date Posted: January 12, 2013 at 6:53 PM
Hardwired Tach signal is Menu 3, Item 2, Opt 4. Then do the Tach Learn process.
-------------
Soldering is fun!
|