I bought two remaned Viper 5704. I attempted the install on my 2002 Dodge Stratus 2.4 Sedan first. The car has no chip or anything in key we use the 2 dollar copies all the time. No oem alarm either. I wired up everything for the remote start first and tried it before soldering the connections. I got the remote start out of manual mode and learned the tach which I wired in instead of using virtual tach. Now when I hit the remote start it says it is running on the remote but the car does not start. I hear the module try to start it three times or so but nothing. The car will however still start with the key. I tried switching the module antenna and remotes to the second one I bought, but the company never paired the remotes to the system so even if I try to ground pulse the H2/21 wire to bypass is it gives me the seven flashes for being in manual mode. Someone please help, maybe I just made a simple error in wiring, this is my first install. I wanted to post a link of the wiring diagram i used but can not find it.
H1/1 Red (+) 12VDC Constant Input -> Battery for now
H1/2 Black (-) Chassis Ground -> goes to ground
H1/3 Brown (+) Siren Output -> Not installed yet
H1/4 WHITE/ Brown Parking light isolation wire -> Not Used?
H1/5 White Parking light output -> Not installed yet
H1/6 Orange (-) Ground when armed -> Not used?
Remote Start
H3/1 Pink Ignition 1 Input/Output -> Tap into blue ignition wire
H3/2 RED / White Fused (30A) Ignition 2 / Flex relay input 87 -> Tap to pink/black const 12v
H3/3 Orange Accessory Output -> Tap to accesory wire, I forgot color but it was at ignition harness and gave voltage at acc. and ign position, but went off at crank
H3/4 Violet Starter Output (Car side of the crank wire) -> Cut yellow Starter wire and connect on the car side of the yellow wire
H3/5 Green Starter Input (Key side of the crank wire) -> Already cut yellow wire connect on the key side of the wire
H3/6 Red Fused (30A) Ignition 1 Input -> Tap to const 12V pink/black wire
H3/7 Pink/White Ignition 2 / Flex Relay Output ->Not used?
H3/8 Pink/Black Flex Relay Input 87A key side (if required) of Flex Relay Not Used?
H3/9 RED / Black Fuse (30A) Accessory/Starter Input -> Tap to const 12V pink/black wire
Auxiliary/Shutdown/Trigger Harness, 24-pin connector
H2/1 Pink/White (-)200mA Ignition / Flex Relay control output -> Not used when doing remote start?
H2/2 BLACK/ White (-) Neutral Safety Input -> Grounded to chassis
H2/3 Blue/White (-)200mA 2nd Status / Rear Defogger Output -> Not used?
H2/4 GREEN/ Black (-)200mA OEM Alarm Disarm Output -> No oem alarm
H2/5 RED / White (-)200mA Trunk Release Output -> Not installed yet
H2/6 Green (-) Door Trigger Input -> Not installed yet
H2/7 BLACK / YELLOW (-)200mA Dome ligh supervision -> Not installed yet
H2/8 BROWN / Black (-)200mA Horn Honk Output -> Not installed yet
H2/9 Dark Blue (-)200mA Status Output -> Not used?
H2/10 Pink (-)200mA Ignition 1 Output - > Not used when doing remote start?
H2/11 WHITE/ Black (-)200mA AUX 3 Output -> Not Used?
H2/12 Violet (+) Door Trigger input -> Not Used
H2/13 WHITE/ Violet Aux 1 Output -> Not Used?
H2/14 Violet/Black Aux 2 Output -> Not Used?
H/2/15 Orang/Black Aux 4 Output -> Not Used?
H2/16 Brown (+) Brake Shutdown Input -> Not installed yet
H2/17 Grey (-) Hood Pin Input -> Connect to wire from the hood pin
H2/18 Violet / YELLOW (-)200mA Starter Output -> Not used when doing remote start?
H2/19 Blue (-) Trunk Pin/ Instant trigger input -> Not used
H2/20 Grey/Black (-) Diesel Wait to start -> N/A
H2/21 WHITE/ Blue (-) Remote start/ Turbo timer activation input -> Not Used?
H2/22 Orange (-) 200mA Accessory Output -> Not used when doing remote start?
H2/23 Violet/White Tachometer input ->Connect to coil wire
H2/24 Green White (-) 200mA OEM Alarm Arm Output -> No oem alarm
Here is the H3 harness :
Remote Start
H3/1 Pink Ignition 1 Input/Output -> Blue Ignition1 wire
H3/2 RED / White Fused (30A) Ignition 2 / Flex relay -> Tap to Pink/Black const 12v
H3/3 Orange Accessory Output -> Tap to BLACK/ Orange Accessory wire
H3/4 Violet Starter Output (Car side of the crank wire) -> Cut yellow Starter wire and connect on the car side of the yellow wire
H3/5 Green Starter Input (Key side of the crank wire) -> Already cut yellow wire connect on the key side of the wire
H3/6 Red Fused (30A) Ignition 1 Input -> Tap to const 12V Pink/Black wire
H3/7 Pink/White Ignition 2 / Flex Relay Output -> GREEN/ Red Ignition2 Set Viper to IGN2 ( Menu 3, Item 8, Opt 1 default )
H3/8 Pink/Black Flex Relay Input 87A Not Used
H3/9 RED / Black Fuse (30A) Accessory/Starter Input -> Tap to const 12V pink/black wire
Here is a note on the Igniton2 wire from Bulldog Security :
GREEN/ RED (+) (20 Gauge wire, 1 of 2, use the one that tests as Ignition)
There should also be a Red +12V constant wire at the ignition harness to use and split-up the load.
For the door locks, use a DEI 451M module ( under $10 ). It comes with the resistors needed for your one-wire door lock system.
The Brake wire should be connected before attempting a remote start.
H2/16 Brown (+) Brake Shutdown Input -> WHITE/ TAN @ SWITCH ABOVE BRAKE PEDAL
-------------
Soldering is fun!
Thanks for the reply! Ill hopefully have a little free time this weekend to give it a second try, i'll post back with results.
Hello, I am attemping to install a remote start on a 2002 Dodge Stratus, I have evrything connected (out of the vehicle) but I can't find a pkch1 bypass module anywhere, is there a substitute bypass module that does not require giving up a key nor downloading firmware?
If not, where can I buy a module with the right firmware pre-loaded and ready to use?
-------------
Millenium Chevy Impala.