clifford 590.2 toggle switch off
Printed From: the12volt.com
Forum Name: Car Security and Convenience
Forum Discription: Car Alarms, Keyless Entries, Remote Starters, Immobilizer Bypasses, Sensors, Door Locks, Window Modules, Heated Mirrors, Heated Seats, etc.
URL: https://www.the12volt.com/installbay/forum_posts.asp?tid=133604
Printed Date: May 11, 2025 at 6:37 AM
Topic: clifford 590.2 toggle switch off
Posted By: adrianotech
Subject: clifford 590.2 toggle switch off
Date Posted: February 15, 2013 at 7:37 PM
Just finished installed a new clifford 590.2x.
everything is working fine beside the remote start.
when activate on the remote, the remote say toggle switch off but its on, anyone know whats going on?.
-------------
ADRIANTECH
Replies:
Posted By: pentavolvo
Date Posted: February 15, 2013 at 8:11 PM
toggle switch broke or ground at end of it came undone
Posted By: adrianotech
Date Posted: February 15, 2013 at 8:14 PM
do you know wich wire suply this function? is it BLACK/ white wire?
-------------
ADRIANTECH
Posted By: pentavolvo
Date Posted: February 15, 2013 at 8:50 PM
on directed products it is. black white is neutral safety switch which must be grounded to remote start. if you use the toggle switch it goes inline on this wire
Posted By: adrianotech
Date Posted: February 16, 2013 at 8:52 AM
I dont get it ,this car is automatic and the remote start has a toggle switch.
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 16, 2013 at 10:28 AM
the black /white is grounded but nothing , what else could be? ------------- ADRIANTECH
Posted By: adrianotech
Date Posted: February 16, 2013 at 11:25 AM
any help please ..
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: February 16, 2013 at 11:59 AM
Did you change the unit to Automatic? Default setting is manal from the factory. Menu 3, Item 1, Option 2
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: February 16, 2013 at 12:02 PM
yes I did it ,still nothing
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 16, 2013 at 12:04 PM
that I dont understand if is in automatic mode why it says toggle switch off
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 16, 2013 at 12:10 PM
could that be a keyless entry installed previewsly ?
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: February 16, 2013 at 12:23 PM
If you could tell us what year, make, and model of vehicle.
Then list all of the wires from the clifford unit connected to what on the vehicle.
Are the connections soldered or some type of clamp/crimp?
What do you mean by a keyless entry installed previously? Is this something you installed? ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: February 16, 2013 at 12:37 PM
honda element 2003, no the keyless entry came installed , and you sent me the wiring connections diagram ,
H3/2, 6, 9, and H1/2 to White 12 volt constant....H3/4 to car side of cut BLACK/ White starter wire, H3/5 to switch side of cut BLACK/ White.... H3/1 to BLACK / YELLOW...H3/3 to BLACK/ Red...
H3/7 to WHITE/ Red,( H3/7 need to be set as ACC2 in the brain of the clifford unit, Default is Ignition 2. Can be changed in Menu 3, Item 8, Option 2)
Test and verify the wires with a Digital Multi Meter BEFORE making your connections. Solder and tape connections. Do Not use T-Taps or scotch locks connectors ------------- ADRIANTECH
Posted By: smokeman1
Date Posted: February 16, 2013 at 12:53 PM
Real Nice...That is what I posted to you on your other topic on this vehicle...
Need to know what wires from the other harness from the clifford are connected to what on the honda...That way I can (SEE) your install ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: February 16, 2013 at 1:12 PM
H1/ 2 RED TO WHITE CONSTANT 12V
H1/ 3 BROWN TO SIREN
H1/ 5 BLACK GROUND
H1/ 8 GREEN TO DOOR TRIGGER LIGHT GREEN & GREEN < size=1 face=DIN-Black>< size=1 face=DIN-Black>
And I Made this diagram from data link DBI-AL(DL)-HA1-EN
------------- ADRIANTECH
Posted By: smokeman1
Date Posted: February 16, 2013 at 4:31 PM
Need to gound the neutral safety input to chassis ground, Either H2/18 on the 18 pin harness or the H2/2 on the 24 pin harness. Whichever you have.
What bypass and did you program it? Did you do Tach Learn? ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: February 16, 2013 at 5:41 PM
Sorry, I forgot to list that one for you I did ground the H2/ 18 neutral safety input
I did program the by pass module for the honda element 2003 but i did not tach learn. ------------- ADRIANTECH
Posted By: adrianotech
Date Posted: February 16, 2013 at 6:09 PM
the Bypass ADSALCA ADS Immobilizer Bypass and Doorlock
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: February 16, 2013 at 8:03 PM
What does happen when you try to remote start? Do the dash lights come on? Does it try to start but stop? Or does nothing happen?
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: February 17, 2013 at 7:33 AM
nothing happens ecxept for one thing when I push the remote control the the parking light flash 8 times .
I look up the startup diagnotics and it says 8 flashs is (neutral safety wire has no ground or the neutral safety switch is off )
but I did grounded the neutral safety wire and the switch is on..... ------------- ADRIANTECH
Posted By: smokeman1
Date Posted: February 17, 2013 at 7:45 AM
Time to recheck the ground on the H2/18, make sure the connector is in tight. Check the toggle switch with a DMM for continunity and make sure it is plugged in tight. Check the H2/18 for continunity also. Until you get that issue cleared it won't start.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: pentavolvo
Date Posted: February 17, 2013 at 8:58 AM
bypass switch all together
Posted By: adrianotech
Date Posted: February 17, 2013 at 12:50 PM
I grounded the ( on ) side of switch and the remote started but I noticed that bypass is not working ,because I had to open the door with the old keyless entry remote control to remote start with the new one....... when I open the door with the old one that allow to start the engine in 30 seconds...
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 17, 2013 at 12:53 PM
so that means the switch was defective.
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 20, 2013 at 9:24 AM
Now I have another isue the remote start works only when I open the door with old keyless remote control , could that be a start kill relay installed previewsly , when I open the door a led start flash rapidly for about 15 seconds , i'm supposed to start the car between open the door to the ligh stop flash rapidly.
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: February 22, 2013 at 8:17 PM
anybody know how to connect the parking lights in element 2003 ?
-------------
ADRIANTECH
Posted By: pentavolvo
Date Posted: February 22, 2013 at 8:27 PM
PARKING LIGHTS ( - ) BLUE (-) @ FACTORY ALARM Plug
NOTE #3; THE FACTORY ALARM PLUG IS LOCATED LEFT OF THE STEERING COLUMN IN A
GREEN PLUG.
Posted By: adrianotech
Date Posted: February 22, 2013 at 8:46 PM
I did it but the light flash just when unlock the door ,not when lock ,not whe start the vehicle... ------------- ADRIANTECH
Posted By: adrianotech
Date Posted: February 23, 2013 at 9:25 AM
any help to connect parking light wires ?
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: March 03, 2013 at 8:45 AM
I can't set ignition controlled door lock unlock on clifford 590.2 it is not responding , is possible set these ficture with data mode on idatalink ? or i have to switch to w2w ?
-------------
ADRIANTECH
Posted By: adrianotech
Date Posted: March 03, 2013 at 5:32 PM
any help please?
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 03, 2013 at 6:31 PM
Need to get into Menu 1, Item 5, Option 1-no lock/unlock, Opt 2, Lock and Unlock, Opt 3 Lock Only, Opt 4 Unlock Only.
You need to access the menus for this. If you can't access the menus, check your wiring and your menu access procedures. Page 11 of install manual. ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 03, 2013 at 7:47 PM
is possible to set those ficture without 3 pin wires from remote start? because im using data mode from the idatalink. ------------- ADRIANTECH
Posted By: adrianotech
Date Posted: March 03, 2013 at 7:49 PM
i dont have a manual install can you copy a link to me?
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 03, 2013 at 8:40 PM
Amazing that you have been installing this without instructions/install manual. No wonder you are having so many issues...Good Luck.
https://www.the12volt.com/installbay/downloads.asp?srch=all&term=5902 Link to THIS SITE down load section. ------------- When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 04, 2013 at 11:50 AM
I'm so sorry man actually I have the installation guide, I tough you had a step by step instruction manual , you're the man , anyways I think I have to hook up the door locks 3pin wires from Remote start brain and disconnect the door lock from I data link, maybe this ficture will work , what I am trying to set is lock after ignition on and unlock ignition off , I have set menu 1, item 5 , option 2 but its not. Working..
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 04, 2013 at 4:00 PM
You get into Menu 1, using the same procedure you used to get into menu 3 to change it from manual to automatic. Only stop at menu 1. How were you able to accomplish that before? Do it again to get to menu 1. Maybe D2D is malfunctioning.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 04, 2013 at 4:26 PM
I did get into the menu 1 and the ficture too but everything sounds to be fine but dont work , like I open the door turn the ignition on and then off press and hold the the botton the siren chirps once i relese the botton and press 5 times and then one more and hold with the remote start i press the open door botton that represent ficture 2. but the door does not unlock after turn ignition off or relese the key.
------------- ADRIANTECH
Posted By: smokeman1
Date Posted: March 04, 2013 at 7:25 PM
Alright, the siren chirps once for menu 1. Does it then chirp 5 times to indicate you are in item 5? Or does it chirp for any item? How many chirps? The alarm will chirp the number for what item you are in. If not, start over and keep trying. I can take a few time to get the hang of it.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 04, 2013 at 7:36 PM
yes the siren chirps once for menu, 5 times for item and chirps for the number of option selected .
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 04, 2013 at 8:20 PM
When you get to Menu1, Item 5, Press the lock OR unlock button until you get two chirps. You should get 1 to 4 chirps for each of the four option for Item 5. You want 2 chirps for ignition lock/unlock. When you get 2 chirps, STOP. let go of the button wait 30-40 seconds for the system to time out of programing, the siren will sound one short blast when the system has exited programming. Hopefully it will stick.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 05, 2013 at 4:41 PM
Hi smokeman1, I did all just the way you told , I heard all chirps and waited until siren sounds ......but nothing.......
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 05, 2013 at 5:29 PM
Don't know what to tell you on it anymore. Maybe you can find someone with a BitWriter that can access the brain to make that setting.
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 05, 2013 at 6:06 PM
what you think i switch to w2w and connect the 3 pin wires from the rs?
-------------
ADRIANTECH
Posted By: smokeman1
Date Posted: March 05, 2013 at 8:24 PM
Worth a try...your call
-------------
When all else fails, Read the Instructions
Support the12volt.com Make a Donation
Posted By: adrianotech
Date Posted: March 05, 2013 at 8:44 PM
Thanks for all your help so far...I really appreciate it.
-------------
ADRIANTECH
|